Grounding Faul Indicator RTU

Grounding fault indicator RTU

User Manual

Content

I. General introduce.

II. Guidance for integrate process.

Ø Hardware parts connection and installation:

Ø Wiring Scheme:

Ø IEC104& DNP3.0 RTU Parameter setting:

III. Terminal RTU upload data

Ø SNV309-EFI, DNP3 Data Objects

Ø SNV309-EFI, IEC104 Data Objects

IV. Attachment for RTU Led blinking define:

User Manual 

Products name: Grounding fault indicator RTU

Model: SNV309-EFI-IEC104/DNP3.0 RTU

Adapt for :

SNOVA ,SNV-EFI, Grounding Fault indicator and EKL series short Grounding fault and short circuit indicator, integrating into SCADA, via 2G/4G network.

I. General introduce.

 SNOVA, Grounding fault indicator RTU, Version SNV309-EFI- IEC104/DNP3.0, it is professional used for SNOVA ,SNV-EFI, Grounding Fault indicator and EKL series short Grounding fault & short circuit indicator, integrating into SCADA, via 2G/4G network. And achieve the grid smart management.

 It support both protocol of DNP3.0 and IEC104 at same time. User need not to do any changes on the device.  It only need to choose different communication port in the user SCADA system. It can integrate by two SCADA system at same time.

II. Guidance for integrate process.Ø Hardware parts connection and installation:

Step 1:

Insert APN sim card into sim card slot （Note: Full size SIM card).

Step 2: Connect GPRS ANTENA on the case terminal.

Step3: Insert the Battery terminal on the PCB.

Step4: Connect Solar power cable via the Solar power panel.

Step5: Connect the EFI between RTU via cables according wiring scheme.

Ø Wiring Scheme:

 Ø IEC104& DNP3.0 RTU Parameter setting:

 Using SNV308&SNV309 parameter setting APP via PC to set this parameter.

1. First connect RTU between computer via data cable.

2. Run the Parameter setting APP on PC.

3. Choose suitable port, and input correct parameter on setting APP interface as below.

3.1 Network parameter

APN:

User name:          (Tips: if the sim card have no user name, then no filled)

Password:            (Tips: if the sim card have no user name, then no filled)

3.2 DNP3.0 protocol parameter

Master link address : 1          

(note: it means SCADA server address, set as :Source in SCADA server)

Slave (Destination) link address:3    

(note: it means RTU address ,set as: Destination  in SCADA server)

Port: 20000

Tips:  According DNP3.0 protocol define, the below setting is standard, normally, it is no need to change. If user SCADA system is really different, then Change it by professionals.

3.3 IEC104 protocol parameter

3.3.1  Msg Timeout. T1  default:  15s

3.3.2  Msg Timeout.T2   default: 10S

3.3.3  Msg Timeout. T3  Default: 30S

Remark:  

T1, T2, T3.  It use for the network state have a timeout value. It makes SCASA system between Terminal communication have a timeout buffer. If want to change, it need to according SCADA system communication speed to adjust the T1,T2,T3 value big or small.  

Suggest, not to change it, otherwise professor is available to change it.

3.3.4 ASDU Address   Default:3.

3.3.5 Port : 2404

(More detail, please contact with the relate Engineer.)

III. Terminal RTU upload data

  The SNV309 -EFI RTU is supported to upload with Max.12 set Grounding fault indicators.

The upload data related the connect number on the SNV309-EFI terminal No. (From 1#, 2#...12#).  Through the SCADA , It can achieve the below main performances.

    1) When Grounding fault indicator detect a grounding fault, then it can upload the fault signal to SCADA.

2)Through SCADA, Operator can operate to Remote reset the indicator, or Test the indicator

Ø SNV309-EFI, DNP3 Data Objects

Supported DNP3 data objects 

1. Binary input - with flags

2. Analog input - single-precision, floating-point with flags

3. Class 0 objects

4. Time and date

5. Binary output - packed format

Annex.list of DNP3.0

Binary input point list (Signal)

Analog input point list (Measure)

Binary output point list

1. Reset EFI

2. Test EFI

Ø SNV309-EFI, IEC104 Data Objects

Annex.list of IEC104

1. Remote signal

ASDU type：

List 1：

2. Remote Measurement

ASDU Type：

List 2：

3. Remote control

ASDU type：

List 3：

List 4：

4. SCADA Timing：

ASDU type：

IV. Attachment for RTU Led blinking define:

1)  The big Green LED on Case outside

2)  LED on PCB in the case