Contact Platform Support
Help CenterPCD235A101 3BHE032025R0101 ABB Central Controller (available From Stock)
Related Products
-
ABB PCD244A101 3BHE042816R0101 Controller Drive Module InventoryUS$ 113 - 260MOQ: 100 Pounds -
PDD200A101 ABB 3BHE019633R0101 Main Control Board Power BoardUS$ 165 - 200MOQ: 100 Pounds
-
PDD205A0121 PDD205A1121 ABB Servo Amplifier Control ModuleUS$ 113 - 200MOQ: 100 Pounds
-
PDD500A101 ABB 3BHE037649R0101 Drive Board Control Board Mainboard CardUS$ 190 - 200MOQ: 100 Pounds
-
PETL101BE 2.0KN 3BSE004214R1 Tension Controller ABB Pillow Block SeriesUS$ 165 - 166MOQ: 100 Pounds
PCD235A101 3BHE032025R0101 ABB Central controller (available from stock)
PCD235A101 3BHE032025R0101 ABB Central controller (available from stock)
Our Email: 2235954483@qq.com
contact number:13313705507
contacts：HE
The trip-circuit supervision is based on a constant current injection principle: by
applying operating voltage for the circuit breaker, a constant current is forced to
flow through the external trip circuit. If the resistance of the trip circuit exceeds a
certain limit, due to oxidation or a bad contact, for instance, the trip-circuit
supervision is activated and a warning appears on the LCD together with a fault
code. The warning signal from the trip-circuit supervision can also be routed to SO2
by setting switch SGF1/8 to 1.
Under normal operating conditions, the applied external voltage is divided between
the relay’s internal circuit and the external trip circuit so that at least 20 V remains
over the relay’s internal circuit. If the external trip circuit’s resistance is too high or
the internal circuit’s too low, due to welded relay contacts, for instance, the voltage
over the relay’s internal circuit falls below 20 V (15...20 V), which activates the tripcircuit supervision.
The operation condition is:
U - R +R +R I 20 V AC/DC c ext int s tc ( )× ≥ (5)
Uc = operating voltage over the supervised trip circuit
Ic = current flowing through the trip circuit, ~1.5 mA
Rext = external shunt resistor
Rint = internal shunt resistor, 1 kΩ
Rs = trip coil resistance
The external shunt resistor is used to enable trip-circuit supervision also when the
circuit breaker is open.
The resistance of the external shunt resistor is to be calculated so that it does not
cause malfunction of the trip-circuit supervision or affect the operation of the trip
coil. Too high resistance causes too high voltage drop, which in turn results in the
operation conditions not being fulfilled, whereas too low resistance may cause
faulty operation of the trip coil.
The following values are recommended for the external resistor, Rext:
Send Inquiry to This Supplier
You May Also Like
-
PFCL201C-10KN/20KN ABB Tension Amplifier (imported From Switzerland)US$ 113 - 166MOQ: 100 Pounds
-
PFCL201CD ABB 3BSE029774R5 Tension Measuring Unit The Weighing SensorUS$ 100 - 200MOQ: 100 Pounds
-
PFCL201CE-10KN/20KN/50KN ABB Tension Pillow Type Load CellUS$ 100 - 200MOQ: 100 Pounds
-
PFEA111-20 3BSE050090R20 ABB Spare Parts for Tension Controller AmplifierUS$ 100 - 200MOQ: 100 Pounds
-
PFEA111-65 3BSE050090R65 ABB The Tension Controller is Brand New and OriginalUS$ 10 - 90MOQ: 100 Pounds
-
PFEA112-20 3BSE050091R20 ABB Tension Sensor Amplifier (sold From Stock)US$ 190 - 260MOQ: 100 Pounds
-
PFEA112-65 3BSE050091R65 ABB Tension Control System Module (in Stock)US$ 190 - 260MOQ: 100 Pounds
-
PFEA113-20 3BSE028144R0020 ABB Tension Electronic ControllerUS$ 165 - 200MOQ: 100 Pounds
-
PFEA113-65 ABB 3BSE028144R0065 Module Control System PartsUS$ 165 - 166MOQ: 100 Pounds
-
PFRA101 3BSE003911R230 ABB New Original Tension ControllerUS$ 100 - 200MOQ: 100 Pounds
