Module spare parts 200-510-017-017 200-510-111-013

Focus on DCS, PLC, robot control system and large servo system.

Main products: various modules / cards, controllers, touch screens, servo drivers.

Advantages: supply of imported original products, professional production parts,

Fast delivery, accurate delivery time,

The main brands include ABB Bailey, Ge / fuanc, Foxboro, Invensys Triconex, Bently, A-B Rockwell, Emerson, ovation, Motorola, xyvom, Honeywell, Rexroth, KUKA, Ni, Deif, Yokogawa, Woodward, Ryan, Schneider, Yaskawa, Moog, prosoft and other brands

Auto-triggering. Trigger setting is too sensitive. • Increase the Insp Trigger setting. • Set a pressure Insp Trigger. • Enable trigger compensation. • Check the patient interface. • Check the expiratory flow sensor. No triggering or missed triggers. Trigger setting is not sensitive enough. • Decrease the flow Insp Trigger setting. • Increase the pressure Insp Trigger setting. Pressure support inspiration is too long. Exp Trigger setting is too low. Tsupp setting is too high. High leak. • Increase the Exp Trigger setting. • Decrease the Tsupp setting. • Check the patient interface. Pressure support inspiration is too short. Exp Trigger setting is too high. Tsupp setting is too low. • Decrease the Exp Trigger setting. • Increase the Tsupp setting. Undesired backup breaths. Minimum Rate is set too high. Decrease the Minimum Rate setting. 8 Alarms and troubleshooting 2065490-001 8-43 General messages General messages show notices, procedures status information, and system status information to the user. General messages show in the lower left corner of the display. The general messages are listed in order of priority from highest to lowest as shown in the table. A 1 indicates a countdown timer is shown with the general message. General Message Inspiratory hold active Expiratory hold active Snapshot created Snapshot deleted Oxygenation1 Nebulizer1 Nebulizer flow compensation on SBT1 Suction1 Suction oxygenation1 Calculating FRC PEEP INview on High Alert Audio off Assist control off Tube compensation on Leak compensation on Bench configuration. Not for patient use. Calibration required. NFS calibration required. CARESCAPE™ R860 8-44 2065490-001 9 Patient monitoring Patient monitoring Patient data and waveforms......................... 9-2 Trends workspace................................9-11 In this section 2065490-001 9-1 Patient data and waveforms Measured data definitions Patient monitoring views show patient data measured by the ventilator and accessories. Some measured data can be viewed with different units. Set unit preferences on the Configuration > Units menu. See "Configuring units" in the "System configuration (Super User) and service" section. Some data is only available when an airway module with the required capabilities, such as spirometry and metabolics, is installed and warmed up. . Gases Data Definition Unit FiO2 The percentage of oxygen that the ventilator delivers to the patient. % EtO2 The percentage of oxygen exhaled, measured at the end of expiration. % EtCO2 The percentage of carbon dioxide exhaled, measured at the end of expiration. %, kPa, or mmHg FI-ET O2 The difference between inspiratory and expiratory concentrations of oxygen. % . Pulmonary Data Definition Unit C The compliance of the patient’s respiratory system measured during the breath cycle. ml/cmH2O, ml/kPa, or ml/ mbar Cstat The static compliance of the patient’s respiratory system measured during an inspiratory hold. ml/cmH2O, ml/kPa, or ml/ mbar Raw The average inspiratory and expiratory airway resistance measured during the breath cycle. cmH2O/l/s, kPa/l/s, or mbar/l/s PEEPe+i The sum of extrinsic and intrinsic positive end expiratory pressures. cmH2O, kPa, or mbar