Contact Platform Support
Help CenterModule Spare Parts N.104-19N.143-18 IB3110050
Related Products
-
Module Spare Parts N.132-18N.143-18 IB3110050US$ 1 - 100000MOQ: 1 Piece -
Module Spare Parts N.145-18N.105-19 IB3110050US$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts 7AO352.70US$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts 7AT664.70US$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts 7DO135.70US$ 1 - 100000MOQ: 1 Piece
Focus on DCS, PLC, robot control system and large servo system.
Main products: various modules / cards, controllers, touch screens, servo drivers.
Advantages: supply of imported original products, professional production parts,
Fast delivery, accurate delivery time,
The main brands include ABB Bailey, Ge / fuanc, Foxboro, Invensys Triconex, Bently, A-B Rockwell, Emerson, ovation, Motorola, xyvom, Honeywell, Rexroth, KUKA, Ni, Deif, Yokogawa, Woodward, Ryan, Schneider, Yaskawa, Moog, prosoft and other brands
N.104-19N.143-18 IB3110050
1. Airway module 2. Gas sample, gas sampling line connector on the water trap 3. Gas sampling and spirometry tubes 4. D-lite(+)/Pedi-lite(+) sensor 5. Spacer (5 ml - minimum) 6. Heat and moisture exchanger with filter (HMEF) (optional) 7. Elbow 8. Gas sampling line To disconnect, follow the steps in reverse order. Airway module calibration Airway module calibration should be performed once every two months or when there is an indication of an error in the gas measurements and waveforms. Use only the calibration gas and regulator specified for the airway module. See "Calibrating the airway module" in the "System configuration (Super User) and service" section. Use only GE Healthcare authorized calibration gas. Do not use other calibration gases or the calibration will not be successful. Dispose of calibration gas containers in accordance with local environmental procedures. During gas calibration, CO2 is always in % regardless of the measurement unit selected. Install this regulator on the gas calibration cylinder: • 755534-HEL (Quick cal regulator) • M1006864 (US only) guard to the inspiratory port. 2. Connect the inspiratory limb of the patient circuit to the inspiratory safety guard. 3. Connect a 5 ml (minimum) spacer at the circuit wye. 4. Connect the Pedi-lite(+) or D-lite(+) sensor to the patient circuit and make the following connections: • Connect the spirometry tubes from the Pedi-lite(+) or Dlite(+) sensor to the airway module. • Connect the gas sampling line from the Pedi-lite(+) or Dlite(+) sensor to the D-fend water trap on the airway module. 5. Connect the heat and moisture exchanger with filter (HMEF) (optional) after the 5ml spacer. 6. Connect an elbow after the HMEF (if used), or after a D-lite or Pedi-lite sensor (if used and an HMEF is not used).
Send Inquiry to This Supplier
You May Also Like
-
Module Spare Parts 7EX470.50-1US$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts 80190-580-51US$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts A402KCUS$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts A4H124-24FX P0973JNUS$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts AUE-1108US$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts CS-1000 UTX1700PTFEUS$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts E33NRHA-LNN-NS-00US$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts ECPSR086370-001US$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts EI813F 3BDH000022R1US$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts EL3040 02402893521100US$ 1 - 100000MOQ: 1 Piece
