1+1 OLP Interface Board for Optical Line Protection
Product description:
OLP Optical Protection Board is a protection system developed by Sharetop Technology Co., Ltd. for optical line backup. It adopts advanced optical path automatic switching module, which is an optical device used in optical fiber communication to switch optical paths. Automatically identify the signal states of the optical signals of the primary and backup optical systems, and perform instantaneous switching of the optical paths so as to protect the primary optical cable from full-impedance failure and protect the system from operating normally and improve the service quality of operators. OLP optical line protection board is widely used in a variety of trunk main and backup protection and a variety of optical switching network. Its advantage is that optical signals can be directly converted into light in the use of optical circuits, small size, economic security, it is used in many optical transmission.
The OLP1: 1 type protection board is designed for protection boards with low loss and redundancy in optical communication lines. The OLP1: 1 type protection board uses the selective receiving and emitting mode to inject light into the backup line to monitor whether there is a fault on the backup line. When the working optical fiber occurs Fault, the receiver and the sender quickly switch to the standby fiber, to ensure unobstructed communication.
Features:
Support single-mode, multi-mode optical line protection.
Support 1 + 1 (dual sending and receiving) protection, 1: 1 (choose the election election) protection.
Support bi-fiber bidirectional and single fiber bidirectional protection.
Support automatic and manual work mode.
Support fiber monitoring
With a wide optical power monitoring range: -50dBm ~ + 23dBm.
With a short optical path protection switching time: ≤ 20ms.
Support power-down optical path state keeping function.
Support local and remote control and SNMP network management.
Performance |
Parameters |
||
wavelength range |
1310±50nm and 1550±50nm |
||
Dynamic range of optical power |
TX: |
+25~-30 dBm |
|
RX: |
+10~-45 dBm |
||
Insertion loss |
1+1 protected |
TX |
≤ 4.0dB |
RX |
≤ 1.5dB |
||
1:1 protected |
≤ 1.5dB |
||
Return loss |
≥45dB |
||
Crosstalk |
≥55dB |
||
Optical power resolution |
≤0.01dB |
||
Optical power measurement accur |
≤0.5dB(+25 dBm ~ -40dBm ) |
||
Wavelength dependent loss |
≤0.25dB |
||
Polarization dependent loss |
≤0.1dB |
||
Switching time |
≤15ms |
||
Working life |
>107 times |
||
Ordering Information:
Optical signal type |
Protection type |
Interface |
S:single-mod |
1:1+1 |
1:LC/UPC |
M:multi-mode |
2:1:1 |
2:LC/APC |
3:1:1(with backup fiber) |
3:SC/UPC |
|
4:1:1(Amplifier) |
4:SC/APC |
|
5:customized |
Send Inquiry to This Supplier
You May Also Like
-
Use for Dwdm Long Hual Distance System PA Pre-amplifier DWDM EDFAUS$ 1250 - 1400MOQ: 1 Piece
-
C-band Erbium Doped Fiber Amplifier Amplifying Optical Signals in Optical Transmission SystemsUS$ 1325 - 1485MOQ: 1 Piece
-
WDM System Optical Line Protection OLP 1+1 Power Supply Backup SystemUS$ 1 - 940MOQ: 1 Piece
-
Communication Equipment 2x32 ABS Module Type PLC Splitter FC APC Connector Optical Fiber Splitter 1.5mUS$ 70 - 72MOQ: 1 Piece
-
G657A Fiber 2x16 ABS Module 2.0mm 1M SC UPC Optic Fiber PLC SplitterUS$ 35 - 37MOQ: 1 Piece
-
2x10/12/16 PLC Splitter LC UPC Connector Optical Fiber Splitter 1.5mUS$ 35 - 37MOQ: 1 Piece
-
G657A Fiber 2x6 2x8 ABS Module 2.0mm 1M FC UPC Optic Fiber PLC SplitterUS$ 21 - 23MOQ: 1 Piece
-
Hot Sale Fiber Cables and Accessories 2x4 PLC Splitter SC APC Connector Optical Fiber Splitter 1.5mUS$ 19 - 20MOQ: 1 Piece
-
FTTB/FTTC/FTTP/FTTH Fiber Optic Splitter ABS Module 2X2 Plc SplitterUS$ 15 - 16MOQ: 1 Piece
-
Hot Sale Fiber Cables and Accessories 2x32 PLC Splitter Without Connector Optical Fiber Splitter 1.5mUS$ 46 - 50MOQ: 1 Piece