Contact Platform Support
Help Center
Related Products
EXIT TABLE IS PROVIDED FOR REMOVING THE FINISHED CORRUGATED SHEETSCORRUGATION MACHINE IS DRIVEN BY AN A. C. MOTOR THROUGH A GEAR REDUCTION DRIVE TRAIN.
· PINCH ROLL ASSEMBLY IS DRIVEN BY A CHAIN & SPROCKET DRIVE ARRANGEMENT THROUGH BOTH THE CORRUGATING ROLLS.
· A FEED TABLE IS PROVIDED WITH GAUGE BLOCKS TO ADJUST THE WIDTH OF THE SHEETS. THIS TABLE IS MOUNTED ON TWO BRACKETS ATTACHED TO THE HOUSING AT BOTH THE SIDES. THIS TABLE SLIDES ON AN ENTRY TABLE.
· THE MOVEMENT OF THE FEED TABLE IS ACHIEVED BY THE CRANK & LEVERS. THE CRANK IS MOUNTED ON THE BOTTOM CORRUGATING ROLL.
· AN ENTRY GUIDE PIPE IS PLACED IN BETWEEN THE ENTRY TABLE AND THE HOUSING, FOR PROVIDING THE ENTRY OF SHEET INTO THE CORRUGATING ROLLS ALONG THE PASS- LINE.
· AN AUXILIARY TABLE IS PLACED BETWEEN THE CORRUGATING ROLL ASSY. AND THE PINCH TOLL ASSY. FOR THE PROPER ENTRY OF THE CORRUGATED SHEETS INTO THE PINCH ROLL ASSY.
· AN .
EXIT TABLE IS PROVIDED FOR REMOVING THE FINISHED CORRUGATED SHEETSCORRUGATION MACHINE IS DRIVEN BY AN A. C. MOTOR THROUGH A GEAR REDUCTION DRIVE TRAIN.
· PINCH ROLL ASSEMBLY IS DRIVEN BY A CHAIN & SPROCKET DRIVE ARRANGEMENT THROUGH BOTH THE CORRUGATING ROLLS.
· A FEED TABLE IS PROVIDED WITH GAUGE BLOCKS TO ADJUST THE WIDTH OF THE SHEETS. THIS TABLE IS MOUNTED ON TWO BRACKETS ATTACHED TO THE HOUSING AT BOTH THE SIDES. THIS TABLE SLIDES ON AN ENTRY TABLE.
· THE MOVEMENT OF THE FEED TABLE IS ACHIEVED BY THE CRANK & LEVERS. THE CRANK IS MOUNTED ON THE BOTTOM CORRUGATING ROLL.
· AN ENTRY GUIDE PIPE IS PLACED IN BETWEEN THE ENTRY TABLE AND THE HOUSING, FOR PROVIDING THE ENTRY OF SHEET INTO THE CORRUGATING ROLLS ALONG THE PASS- LINE.
· AN AUXILIARY TABLE IS PLACED BETWEEN THE CORRUGATING ROLL ASSY. AND THE PINCH TOLL ASSY. FOR THE PROPER ENTRY OF THE CORRUGATED SHEETS INTO THE PINCH ROLL ASSY.
· AN .
· GEARS ARE PROVIDED AT BOTH THE ENDS OF TOP & BOTTOM CORRUGATION ROLLS TO ADJUST & KEEP THE CRESTS IN CENTRE.
EXIT TABLE IS PROVIDED FOR REMOVING THE FINISHED CORRUGATED SHEETS<span style="" font-family:"="">.
· GEARS ARE PROVIDED AT BOTH THE ENDS OF TOP & BOTTOM CORRUGATION ROLLS TO ADJUST & KEEP THE CRESTS IN CENTRE.
Send Inquiry to This Supplier
You May Also Like
-
Cone-rolling MachineUS$ 30000 - 30000MOQ: 1 Set -
Oil and Gas Transmission Pipe Bending MachineUS$ 650000 - 650000MOQ: 1 Set
-
Long Pipe Rolling Machine/plate Bending MachineUS$ 650000 - 650000MOQ: 1 Set
-
Huge Four-roller Plate Bending MachineUS$ 800000 - 800000MOQ: 1 Set
-
NC Four-roller Plate BendingUS$ 300000 - 300000MOQ: 1 Set
-
Hydraulic 4-roller Bending RollsNegotiableMOQ: 1 Set
-
Four-roller Bending Machine for Wind TowerNegotiableMOQ: 1 Set
-
Hydraulic 4-roller Bending RollsNegotiableMOQ: 1 Set
-
Oil and Gas Transmission Pipe Bending MachineNegotiableMOQ: 1 Set
-
CNC Four-roller Plate Rolling MachineUS$ 5000 - 1000000MOQ: 1 Set
