Contact Platform Support
Help CenterModule Spare Parts YOKOGAWA CP451-50
Related Products
Focus on DCS, PLC, robot control system and large servo system.
Main products: various modules / cards, controllers, touch screens, servo drivers.
Advantages: supply of imported original products, professional production parts,
Fast delivery, accurate delivery time,
The main brands include ABB Bailey, Ge / fuanc, Foxboro, Invensys Triconex, Bently, A-B Rockwell, Emerson, ovation, Motorola, xyvom, Honeywell, Rexroth, KUKA, Ni, Deif, Yokogawa, Woodward, Ryan, Schneider, Yaskawa, Moog, prosoft and other brands
| YOKOGAWA CP451-50 |
1. Thumbscrew 2. Excess cable 3. Module bay connection 4. Module bay cable 5. Ventilator airway module bay connection 5. Slide the airway module into the upper portion of the airway module bay. 6. Attach the tubing to the airway module. To disconnect the airway module bay: • Remove the airway module from the airway module bay. • Remove the cable from the airway module bay from the back of the ventilator. • Loosen the airway module bay thumbscrews and remove the airway module bay. Note 4 Setup and connections 2065490-001 4-29 Connecting the Pedi-lite(+) and D-lite(+) sensors Use the Pedi-lite(+) sensor for patients with tidal volumes up to, and including 200 ml. Use the D-lite(+) sensor for patients with tidal volumes greater than 200 ml. To ensure patient safety, make sure that the gas sampling connectors are connected as described in these instructions and are not interchanged with connectors on other equipment. The D-lite(+) and Pedi-lite(+) sensors have a port to provide gas samples to the airway module. Both sensors are available as reusable (yellow) or disposable (clear). Airway pressures are measured between the patient wye and the patient airway with a D-lite(+) or Pedi-lite(+) sensor. The sensors have a two-sided Pitot tube used to measure pressure. The pressure difference across a flow restrictor is used to calculate flow. From the flow, inspiratory volume and expiratory volume are calculated. 1. Connect the inspiratory safety guard to the inspiratory port. 2. Connect the inspiratory limb of the patient circuit to the inspiratory safety guard. 3. Connect a 5 ml (minimum) spacer at the circuit wye. 4. Connect the Pedi-lite(+) or D-lite(+) sensor to the patient circuit and make the following connections: • Connect the spirometry tubes from the Pedi-lite(+) or Dlite(+) sensor to the airway module. • Connect the gas sampling line from the Pedi-lite(+) or Dlite(+) sensor to the D-fend water trap on the airway module. 5. Connect the heat and moisture exchanger with filter (HMEF) (optional) after the 5ml spacer. 6. Connect an elbow after the HMEF (if used), or after a D-lite or Pedi-lite sensor (if used and an HMEF is not used).
Send Inquiry to This Supplier
You May Also Like
-
Module Spare Parts N.104-19N.143-18 IB3110050US$ 1 - 100000MOQ: 1 Piece -
Module Spare Parts N.132-18N.143-18 IB3110050US$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts N.145-18N.105-19 IB3110050US$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts 04220FL11232AUS$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts 05701-A-0301US$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts 05701-A-0302US$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts 05701-A-0325US$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts 05701-A-0326US$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts 05701-A-0329US$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts 05701-A-0502US$ 1 - 100000MOQ: 1 Piece
