Contact Platform Support
Help Center1.25G SFP Optical Transceiver With DDM Mornitor
Related Products
-
3Gbps Video SFP Optical Transceiver | SFP ModuleUS$ 100 - 150MOQ: 1 Unit -
1.485Gbps Video SFP Optical TransceiverUS$ 100 - 150MOQ: 1 Unit
-
155M SFP Optical TransceiverUS$ 100 - 150MOQ: 1 Unit
-
155M SFP Optical TransceiverUS$ 100 - 150MOQ: 1 Unit
-
40Gb/s 40km QSFP+ TransceiverUS$ 100 - 150MOQ: 1 Unit
FEATURES:
Up to 1.25Gb/s data links
Hot-pluggable SFP footprint
1310nm Fabry-Perot laser transmitter
Duplex LC connector
Compliant with SFP MSA and SFF-8472
Digital Diagnostic Monitoring(DDM):Internal Calibration or External Calibration
Very low jitter
No Rate Select input required for
Fiber Channel 1x/2x Operation
Up to 20km on 9/125μm SMF
Metal enclosure, for lower EMI
Single 3.3V power supply
Low power dissipation
CWDM is also Available
Class 1: FDA/IEC60825-1 Laser Security
APPLICATIONS:
Gigabit Ethernet
1x Fiber Channel
Switch to Switch interface
Switched backplane applications
Router/Server interface
Other optical transmission systems
Description:
BDTRP413L1SD-20 Small Form Factor Pluggable (SFP) transceivers are compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA).They comply with laser safety standard IEC-60825 and Ethernet standard IEEE802.3z 1000Base-LX/LH and IEEE802.3ah.
The transceiver consists of two sections: The transmitter section incorporates a FP laser. the receiver section consists of a PIN photodiode integrated with a trans-impedance preamplifier (TIA).
All modules satisfy class I laser safety requirements. The optical output can be disabled by a TTL logic high-level input of Tx Disable. Tx Fault indicates that degradation of the laser. Loss of signal (LOS) output indicates the loss of an input optical signal of receiver. The SFP module can be compatible with other brand switch devices like Cisco,Huawei etc.The SFP module has the function of AGC (Automatic Gain control without attenuator).
Optical Characteristics (TOP = 0 to 70℃, VCC = 3.00 to 3.60 Volts) Notes: 1. Class 1 Laser Safety per FDA/CDRH and EN (IEC) 60825 regulations. 2. Also specified to meet curves in FC-PI 13.0 Figures 18 and 19, which allow trade-off between wavelength, spectral width and OMA. 3. Equivalent extinction ratio specification for Fiber Channel. Allows smaller ER at higher average power. 4. Unfiltered, 20-80%. Complies with IEEE 802.3 (Gig. E), FC 1x and 2x eye masks when filtered. 5. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ and DDJ. 6. Measured with conformance signals defined in FC-PI 13.0 specifications.
7. Measured with PRBS 27-1 at 10-12 BER
Send Inquiry to This Supplier
You May Also Like
-
SFP+ Direct Attach Passive Copper CablesUS$ 80 - 150MOQ: 1 Unit
-
Hybrid Passive Copper 100GE QSFP28 to 4x 25GE SFP28US$ 80 - 150MOQ: 1 Unit
-
10G Bi-Directional SFP+ Optical TransceiverUS$ 100 - 150MOQ: 1 Unit
-
10Gb/s XFP Optical TransceiverUS$ 100 - 150MOQ: 1 Unit
-
10Gbps DWDM XFP 40KmUS$ 100 - 150MOQ: 1 Unit
-
10Gbps DWDM XFP 80KMUS$ 100 - 150MOQ: 1 Unit
-
10G XFP BIDI TransceiverUS$ 100 - 150MOQ: 1 Unit
-
CWDM 10G XFP Optical ModuleUS$ 100 - 150MOQ: 1 Unit
-
BDTRP653S1SN-20 2.5G SFP TransceiverUS$ 100 - 150MOQ: 1 Unit
-
EPON GPON ONU Stick SFP Module With MAC InsideUS$ 100 - 150MOQ: 1 Unit
