Contact Platform Support
Help CenterBently Nevada 45358-09 – Extension Cable for Proximity Probe Systems
Related Products
-
Bently Nevada 3500/33-SIL-01 Relay Module – Safety-rated Alarm Relays for the 3500 Protection SystemNegotiableMOQ: 1 Combo -
Bently Nevada 330130-045-00-00 Extension Cable – 3300 XL Proximity System CablingNegotiableMOQ: 1 Combo
-
Bently Nevada 125680-01 Sensor Module – Purpose-built for Centrifugal Compressor MonitoringNegotiableMOQ: 1 Combo
-
Bently Nevada 330130-040-00-05 Extension Cable – for 3300 XL Proximity Transducer SystemsNegotiableMOQ: 1 Combo
-
Bently Nevada RAO00027 Accelerometer – Casing Vibration Sensor for Centrifugal CompressorsNegotiableMOQ: 1 Combo
The Bently Nevada 45358-09 is a factory-terminated extension cable designed for proximity probe systems used in critical rotating machinery. It typically links the probe to the Proximitor sensor, preserving signal fidelity over distance so your vibration and position data stays clean and dependable. In many cases it’s specified in 3300/3500-series monitoring architectures where long, stable runs are needed through harsh plant areas.
Key FeaturesSystem-matched connectivity – Uses Bently Nevada-standard miniature coax terminations for a direct fit to probes and Proximitor sensors.
Signal integrity over distance – Engineered to maintain eddy-current probe signals and DC gap voltage with minimal attenuation and noise pickup.
Rugged industrial build – Jacket and dielectric materials are chosen for reliability in plant environments; routing through tray or conduit is straightforward.
Length-coded suffix – The “-09” suffix designates a specific factory length variant in this series (confirm exact length against your BOM before ordering).
Drop-in replacement – From my experience, it simplifies spares management for sites standardizing on Bently Nevada proximity measurement chains.
| Brand / Model | Bently Nevada 45358-09 |
| Product Type | Proximity probe extension cable (miniature coax) |
| Power Requirements | None (passive cable) |
| Signal Types | Eddy-current proximity probe signals (dynamic vibration + DC gap voltage) |
| Connectors | Bently Nevada standard miniature coax terminations (probe-to-Proximitor chain) |
| Length Variant | “-09” denotes a specific factory length; verify per system BOM |
| Operating Temperature | Industrial-grade range; follow system specification and routing practices |
| Installation Method | Cable tray or conduit; probe-to-Proximitor interconnect within control cabinet or field run |
| Compatibility | Bently Nevada proximity measurement chains (e.g., 3300/3500 architectures), as specified |
You’ll typically see the 45358-09 in vibration and position monitoring loops on:
Steam and gas turbines (radial/axial position, shaft vibration)
Compressors and expanders in petrochemical plants
Large motors, generators, and gearboxes
Pumps and fans where bearing health and shaft dynamics matter
One maintenance lead at a combined-cycle site told me their move to standardized Bently Nevada cabling cut troubleshooting time because “every connector just fits, and the signal stays stable after shutdowns.”
Risk reduction – Correct impedance and shielding help avoid intermittent faults and noisy baselines that hide early fault signatures.
Guaranteed fit – Mates to probes and Proximitor sensors without adapters; seems to be the cleaner path than mixed-vendor assemblies.
Lifecycle efficiency – Standardized spares by suffix shortens lead times and simplifies PM planning.
Supportability – Easier to document in machine files and P&IDs; in most cases, supported under OEM diagnostic guidelines.
Routing – Run in tray or conduit away from high-voltage lines and VFD outputs; maintain generous separation from EMI sources.
Bend radius – Keep bends smooth; avoid tight radii and pinch points that can deform the dielectric.
Terminations – Seat miniature coax connectors fully; finger-tighten as specified and avoid over-torque.
Grounding – Follow the plant’s grounding and shielding scheme; bond shields per OEM practice at the appropriate end.
Environmental – If in hot zones, use protective conduit; check for oil/chemical exposure and mechanical abrasion.
Routine checks – Inspect connectors during outages, verify continuity, and confirm stable DC gap voltage after reassembly.
Manufactured to OEM standards for Bently Nevada proximity measurement systems
CE/RoHS compliance typically applicable at the system level; check project documentation
Warranty: commonly 12 months from shipment for new OEM-supplied parts
Proximity probe (Bently Nevada 3300/3300 XL series, length as per machine point)
Proximitor sensor module matched to the probe/cable set
Monitoring rack/module (e.g., Bently Nevada 3500) for trending and protection
If you’re matching an installed base, a quick cross-check of probe model, cable suffix “-09”, and Proximitor part number against the machine’s BOM usually prevents surprises.
Send Inquiry to This Supplier
You May Also Like
-
Bently Nevada 330105-02-12-10-12-05 Proximity Probe for Shaft Vibration and PositionNegotiableMOQ: 1 Combo
-
Bently Nevada 330101-00-48-10-02-05 Proximity Probe for Vibration and Shaft Displacement MonitoringNegotiableMOQ: 1 Combo
-
Bently Nevada 3500/60 133819-01 – Four‑channel Temperature Monitor for Critical Machinery ProtectionNegotiableMOQ: 1 Combo
-
Bently Nevada 3500/20 125744-02 – Rack Interface Module for 3500 Machinery ProtectionNegotiableMOQ: 1 Combo
-
Bently Nevada 3500/60 133811-01 Temperature Monitor – Multi‑channel Temperature Protection for Critical Rotating AssetsNegotiableMOQ: 1 Combo
-
Bently Nevada 3500/92 (P/N 136180-01) – Communications Gateway for 3500 Machinery Protection RacksNegotiableMOQ: 1 Combo
-
BENTLY 3500/60 163179-01 – Temperature Monitoring Module for Critical Rotating EquipmentNegotiableMOQ: 1 Combo
-
Bently Nevada 3500/92 133323-01 – Communications Gateway for the 3500 Machinery Protection RackNegotiableMOQ: 1 Combo
-
Bently Nevada 3500/15-05-00-00 Power Supply – Core AC Module for 3500 Series RacksUS$ 4216.00MOQ: 1 Blade
-
BENTLY NEVADA 125744-01 – 3500 Series Module for Vibration Monitoring and Machine ProtectionUS$ 4216.00MOQ: 1 Blade
