Contact Platform Support
Help CenterGE 04240FD11234A – OEM Replacement Module for GE Industrial Control Systems
Related Products
-
ABB RED670 – High‑speed Line Differential Protection for Transmission Lines and CablesNegotiableMOQ: 1 Combo -
ABB LD800HSEEX 3BSE073314R1 – Ex-rated FOUNDATION Fieldbus H1 to HSE Linking Device for System 800xANegotiableMOQ: 1 Combo
-
ABB CR-U230AC3L (1SVR405622R3100) – 230 VAC Plug-in Control Relay for Reliable 3CO SwitchingNegotiableMOQ: 1 Combo
-
ABB DO880 (3BSE028602R1) – High‑integrity Digital Output Module for S800 I/O and AC 800MNegotiableMOQ: 1 Combo
-
ABB REF615 HBFFAEAGNBA1ANB1XD – Feeder Protection & Control for Medium-Voltage DistributionNegotiableMOQ: 1 Combo
The GE 04240FD11234A is an original GE spare part used as a direct-fit replacement in GE industrial control assemblies. It’s typically selected to restore failed boards or submodules in drive cabinets, PLC racks, or protection/control panels without redesign work. From my experience, matching by this exact part number and suffix is the fastest way to get a system back online with minimal requalification.
OEM direct replacement – Ensures mechanical fit and interface compatibility with the original GE assembly.
Revision-controlled – The “FD1…A” sequence helps maintenance teams match revisions across installed bases; reduces compatibility surprises.
Service-friendly design – Typically installs as a board-level or module swap; no field rewiring in most cases.
Traceable labeling – Full part number and revision markings support documentation control and audits.
Built for industrial duty – Intended for use inside GE control panels where vibration, electrical noise, and 24/7 duty are normal.
Downtime reduction – Keeps lines running by replacing like-for-like; no software redesign if you match the exact P/N.
| Brand / Model | GE 04240FD11234A |
| Product Type | OEM replacement module/board for GE industrial control equipment |
| Power Requirements | Supplied by host system (board-level power); refer to the host equipment manual |
| Signal I/O | As implemented in the original GE assembly; depends on system configuration |
| Communication Interfaces | If present, matches the original module configuration (check P/N and revision) |
| Installation Method | Direct swap-in within the existing GE control/drive/PLC rack or panel location |
| Operating Temperature | Per host equipment specification |
| Compatibility | Match by complete P/N “04240FD11234A” and installed system part references |
You’ll typically find this part used as a service replacement inside GE automation cabinets—think variable-speed drives, PLC/remote I/O enclosures, and protection or control panels on process lines. It seems to be deployed where a like-for-like module swap is preferred over changes to wiring or firmware. One maintenance lead at a beverage plant told us a similar FD-series part brought their filler line back in under an hour.
Advantages & ValueRisk reduction – Direct replacement minimizes engineering changes and validation time.
Lifecycle continuity – Keeps legacy GE systems operational without forcing a platform upgrade.
Procurement clarity – Exact P/N sourcing avoids guesswork on cross-references.
Cost control – In many cases, a module swap is far cheaper than a full rack retrofit or redesign.
Technical support – Part number traceability makes it easier for service teams to provide targeted guidance.
Environment – Install inside a suitable enclosure (NEMA/IEC cabinet) with clean airflow and proper grounding.
Power-down & ESD – Isolate all power, discharge stored energy, and use ESD protection; handle boards by the edges.
Wiring & seating – If connectors are involved, reseat fully with latch engagement; avoid pin stress or misalignment.
Firmware/config – Where applicable, back up parameters from the original unit and verify version compatibility before final start-up.
Routine checks – Inspect connectors for oxidation, clean dust from the cabinet, and document part numbers/revisions for future call-outs.
Manufacturing quality – Produced under GE quality systems (typically ISO 9001).
Compliance – CE/UL/RoHS status is determined at the system level; the module follows the host assembly’s approvals.
Warranty – Commonly supplied with a limited warranty period via authorized channels; keep your purchase documentation.
You might notice the part number suffix and revision code matter a lot with this series. If you can share the installed system model or a photo of the nameplate, we can double-check interchangeability before you schedule downtime.
Send Inquiry to This Supplier
You May Also Like
-
ABB 520PSD01 – Power Distribution Module for Stable Backplane Power in Process AutomationNegotiableMOQ: 1 Combo
-
ABB CI854AK01 (3BSE030220R1) – PROFIBUS DP Interface Module for AC 800M ControllersNegotiableMOQ: 1 Combo
-
GE IC200GBI001 – VersaMax Genius Bus Interface for Reliable Remote I/O on Legacy and Mixed NetworksNegotiableMOQ: 1 Combo
-
ABB SD812F (3BDH000014R1) – System Power Supply for AC 800F / Freelance Controller StationsNegotiableMOQ: 1 Combo
-
ABB FPR3203526R1002A – OEM Replacement Module for Industrial Control and Drives SystemsNegotiableMOQ: 1 Combo
-
ABB 3BHB012873R0004 – Drive Power/IGBT Interface Board for ABB Low-Voltage AC DrivesNegotiableMOQ: 1 Combo
-
ABB PFEA111-65 (3BSE050090R65) – Tension Electronics for Reliable Web and Strip MeasurementNegotiableMOQ: 1 Combo
-
ABB PCD235A101 (3BHE032025R0101) – High‑speed Control Processor for AC 800PECNegotiableMOQ: 1 Combo
-
ABB SDCS-COM-5 (3BSE006567R0001) – Communication Interface Board for DCS DC DrivesNegotiableMOQ: 1 Combo
-
ABB SK827005 & SK827100-AS – Genuine OEM Spare/Service Kit Assemblies for ABB SystemsNegotiableMOQ: 1 Combo
