Contact Platform Support
Help CenterModule Spare PartsDS200TBQCG1AAA
Related Products
-
Module Spare Parts DS200TBQDG1AFFUS$ 1 - 100000MOQ: 1 Piece -
Module Spare Parts DS200TCCAG1BAAUS$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts DS200TCEAG1ACBUS$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts DS200TCEAG1BNE DS215TCEAG1BZZ01AUS$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts DSQC604 3HAC12928-1US$ 1 - 100000MOQ: 1 Piece
Focus on DCS, PLC, robot control system and large servo system.
Main products: various modules / cards, controllers, touch screens, servo drivers.
Advantages: supply of imported original products, professional production parts,
Fast delivery, accurate delivery time,
The main brands include ABB Bailey, Ge / fuanc, Foxboro, Invensys Triconex, Bently, A-B Rockwell, Emerson, ovation, Motorola, xyvom, Honeywell, Rexroth, KUKA, Ni, Deif, Yokogawa, Woodward, Ryan, Schneider, Yaskawa, Moog, prosoft and other brands
| DS200TBQCG1AAA |
A Phillips screwdriver is required to install the switch into a rack. Unpacking the Switch Unpack the switch as follows: 1. Open the box and remove the packing material protecting the switch. 2. Verify that the contents of the carton contains the items listed in the table below. 3. Remove the tape seal on the non‐conductive bag to remove the switch. 4. Perform a visual inspection of the switch for any signs of physical damage. Contact Enterasys Networks if there are any signs of damage. Refer to “Getting Help” on page xvii for details. Installing the Switch on a Flat Surface When installing the switch on a flat surface, the installation of the rubber feet is recommended to prevent the switch from sliding on a flat surface. For instructions to rack mount the switch, proceed to “Rack Mounting the Switch” on page 2‐3. Installing the Rubber Feet To install the rubber feet: 1. Place the switch on its back on a sturdy flat surface to gain access to the bottom of the chassis. 2. Remove the four rubber feet from their plastic bag in the shipping box. 3. Remove the protective strip from the back of one rubber foot and position it on a corner and press firmly into place. Repeat this procedure to install the remaining three rubber feet in the other three corners. 4. After installing the rubber feet, return the switch to its upright position. If a number of switches are being installed in a stack, repeat steps 1 through 4 to install the rubber feet on each switch before continuing with the installation.• IEEE 802.3ad • Full‐Duplex operation In addition to the 100BASE‐T standards, the SFP ports are compliant with the following standards and operations: • IEEE 802.3z • IEEE 802.3x Flow Control support for Full‐Duplex mode
Send Inquiry to This Supplier
You May Also Like
-
Module Spare Parts DSQC679 3HAC028357-001US$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts DT602 GJR2911200R1US$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts DT680E GJR2923100R1 DT680B-EUS$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts FC-TSAI-1620MUS$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts FI820F 3BDH000031R1US$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts FI830F 3BDH000032R1US$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts FLN3524AUS$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts FLN4234AUS$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts FM265AUS$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts FM9925a-EUS$ 1 - 100000MOQ: 1 Piece
