Contact Platform Support
Help CenterCI867AK01 3BSE092689R1 ABB New Imported Warehouse Spot Module
Related Products
-
CI867K01 3BSE043660R1 ABB Communication Interface Kit (available in Stock)US$ 100 - 200MOQ: 100 Pounds -
ABB New DCS Module Ci868k01-ea Control System Module 3bse048845r2 BargainingUS$ 100 - 200MOQ: 100 Pounds
-
CM572 CM572-DP CM572-DP-XC ABB AC500 PLC Communication ModuleUS$ 10 - 90MOQ: 100 Pounds
-
CM772F 3BDH000368R0001 ABB DCS Ac700f Communication ModuleUS$ 100 - 200MOQ: 100 Pounds
-
CMA120 3DDE300400 ABB As Panel Controller Panel Complete MachineUS$ 100 - 200MOQ: 100 Pounds
CI867AK01 3BSE092689R1 ABB New imported warehouse spot module
CI867AK01 3BSE092689R1 ABB New imported warehouse spot module
Our Email: 2235954483@qq.com
contact number:13313705507
contacts：HE
The NGC8206 must be properly grounded. The NGC has a grounding lug on the
mounting neck of the enclosure. This lug should be tied to a good earth ground
with no smaller than #12AWG wire. The NGC8206 cannot be connected to any
pipeline where cathodic protection exists. If the system uses cathodic protection,
the NGC must be mounted on a section of pipe that has been electrically isolated
from the cathodic currents (see Figure 1—16).
1.4.1 Power Supply
The power supply for the NGC should have an isolated output (i.e., the negative
side of the 12VDC output should not be electrically connected to chassis or earth
ground). In many instances, the power supply is collocated with a radio. If the
radio is connected to the NGC8206 via RS232/485/422, the communications
should share the power ground. The communication shield should only be
connected at the NGC end. The other end should be left to float (left
unconnected).
1.4.2 Sample Probe
If the sample probe is mounted to a section of pipe where cathodic currents may
exist, the user needs to put isolators in the sample tubing between the sample
probe and the NGC. Any time that the sample probe is on a section of pipe other
than the one where the NGC is directly mounted, tubing isolators should be
employed. It is very important that probe ground and the NGC ground be at the
same potential. If this cannot be insured, tubing isolators must be used.
Send Inquiry to This Supplier
You May Also Like
-
CMA131 3DDE300411 CMA132 3DDE300412 ABB CMA136 3DDE300416 in StockUS$ 100 - 200MOQ: 100 Pounds
-
COM0002 COM0003 ABB New Control PanelUS$ 100 - 166MOQ: 100 Pounds
-
CP405 ABB Cp400 Series HMI Human Machine Interface Touch ScreenUS$ 10 - 260MOQ: 100 Pounds
-
CP430T-ETH 1SBP260196R1001 ABB Man Machine Touch ScreenUS$ 165 - 260MOQ: 100 Pounds
-
CP435T 1SBP260193R1001 ABB Industrial Touch Screen in StockUS$ 113 - 166MOQ: 100 Pounds
-
CP450-T-ETH ABB Touch Screen Human Machine Interface 1SBP26188R1001US$ 113 - 200MOQ: 100 Pounds
-
CS513 3BSE000435R1 ABB Card Ci535v30 / 3bse022162r1 (spot)US$ 190 - 200MOQ: 100 Pounds
-
CSA463AE CSA464AE ABB Module Motherboard Card Controller (in Stock)US$ 165 - 200MOQ: 100 Pounds
-
D685A1156U01 ABB Card Module Controller in StockUS$ 165 - 260MOQ: 100 Pounds
-
DCP02 DCP10 Robot System Card ABB Imported ModuleUS$ 100 - 200MOQ: 100 Pounds
