Contact Platform Support
Help CenterAnchor Extruder For Post Tensioning In Promotion
Related Products
-
Colloidal Grout Mixer|IntellegentUS$ 3000 - 4500MOQ: 1 Piece -
Multi Strand Jack Lifting SystemUS$ 1500 - 3000MOQ: 1 Piece
-
Hydraulic Stressing Jack|Multi StrandUS$ 15000 - 30000MOQ: 1 Piece
-
Mono Strand Pulling JackUS$ 800 - 2000MOQ: 1 Piece
-
Post Tension Mono Strand Hydraulic JackUS$ 800 - 2000MOQ: 1 Piece
Features of Anchor Extruder For Post Tensioning:
1 prestressed extrusion method is simple and reliable, the machine is easy to use, high efficiency, every hour can squeeze 20-30 extruding anchor.
2 handling lightweight, durable, easy operation and convenient maintenance.
Customer first, service first.
Introduction of Anchor Extruder For Post Tensioning:
Anchor Extruder for Post Tensioning is composed of a front beam, a main oil cylinder pin, pin nut, prestress, frame composed of several parts, mainly used for steelCompression Fitting Machine, connection.
Application of Anchor Extruder For Post Tensioning:
The Anchor end extruder is used for extrusion and connection of steel strand extrusion sleeve. It is a kind of specialized equipment used for cold extruding steel strand wrapping anchor work. The Swage Anchor Extruder is used for single end anchorage of stranded steel strands of 12- Phi 15.7
Parameters of Anchor Extruder For Post Tensioning:
Nominal pressure KN |
519 |
piston extrusion surface ㎡ |
1.039X10 |
Nominal oil mpa |
50 |
return piston area of㎡ |
4.948X10 |
extrusion stroke mm |
150 |
Quality ㎏ |
43 |
With the pump |
ZB-500 |
Dimensions mm |
148X545 |
Points for attention in use of four Anchor Extruder for Post Tensioning:
When installing an extrusion sleeve, the prestressed steel strand is pressed into a good steel strand according to a predetermined length, and then is inserted into an extrusion spring and an extrusion sleeve after being turned down, and is extruded and formed on an extruder
Extrusion process;
1 connect the extruder and oil pump and connect the power supply
2 apply the wetted grease on the extrusion die
3 press the spring into the steel strand and go through the extruding die of the press
4 press the sleeve on the top of the steel wire extrusion spring
The oil pump is used to supply oil to the extruder, and the extruding sleeve is extruded through the extruding die, and the extruding sleeve is thinned and nested on the steel strand
Matters needing attention Prestressed strand extrusion machine
Extrusion through extrusion mode, the maximum oil pressure should be between 25-38Mpa
After the extrusion of the extrusion sleeve, the bottom and the steel strand are required to be closely nested, and the extrusion spring shall be embedded between the extruding sleeve and the steel strand
The length and the outer diameter of the extrusion sleeve shall be consistent with the manufacturer's given value, and the outer surface shall be smooth and free of cracks
Send Inquiry to This Supplier
You May Also Like
-
Prestressed Mono Strand Post Tension Hydraulic JackUS$ 800 - 2000MOQ: 1 Piece
-
Hydraulic Single Cylinder Mono Strand Jack TensioningUS$ 800 - 2000MOQ: 1 Piece
-
Single Cylinder Hydraulic Jack TensioningUS$ 800 - 2000MOQ: 1 Piece
-
Hydraulic Single PC Strand Stressing JackUS$ 350 - 500MOQ: 1 Piece
-
Mono Strand Stressing Jack Used in Bridge ConstructionUS$ 350 - 390MOQ: 1 Piece
-
65-600 Tons Hydraulic Stressing Jack With Multi-StrandsUS$ 550 - 5000MOQ: 1 Piece
-
Ydc2000 Hydraulic Stressing Jack With Multi-StrandsUS$ 650 - 5000MOQ: 1 Piece
-
Hydraulic Stressing Jack With Multi-StrandsUS$ 650 - 5000MOQ: 1 Piece
-
50-500t Multi PC Strands Stressing Jack Post Tension Jack in ConcreteUS$ 650 - 2000MOQ: 1 Piece
-
Multi-Strands Stressing Jack Equipment Including Oil PumpUS$ 500 - 3500MOQ: 1 Piece
