Home > Products > brakes > Hydraulic Safety Emergency Brake SBD365-C Casting Crane Hengyang Heavy Industry
Hydraulic Safety Emergency Brake SBD365-C Casting Crane Hengyang Heavy Industry
- 700 Unit / Units per Month
- PayPal
Product Description
SBD-A Safety Disc Brake Selection
Disc brakes can be divided into three categories: b, c, and d. Category b has a brake assist device installed on the brake, which is conducive to safe use, but the system requires a larger cost.
Installation
3.2.1 Mounting the Brake on a Bracket
If the user orders with mounting bracket and fastening bolts, the bracket and brake caliper will be mounted and supplied together before delivery, so this work can be omitted.
a. Remove oil and dust from the mating surfaces of the caliper and mounting bracket, and lift the caliper onto the bracket with a crane. Note: The side with the exhaust fitting (piece 8 in Fig. 1) must be facing upwards;
b. Fasten the brake caliper with 8 high-strength bolts, the strength of the nut must be more than 12.9 grade, with nylon locking inserts, flat pads for the
45 steel tempered HRC35~45;
c. The bolts must be tightened using a torque plate hand, tightening torque as shown in Table 1.
3.2.2 Hydraulic connection and brake cylinder venting
a. Before installing the brake, the hydraulic station should be installed and debugged (please refer to the instruction manual of the hydraulic station for the installation and debugging of the hydraulic station), and the hydraulic pipeline should be well lined up, the thread of the brake cylinder oil inlet connector should be M18X1.5, and the diameter of the hydraulic pipeline should be more than 10mm, and the total oil inlet required when the brake is backed up by 2mm should be shown in Table 1;
It must be ensured that the length of the pipeline from all brake cylinders to the hydraulic station is equal!
Before using and adjusting the brake, the brake cylinder should be ventilated as follows: there is a dual-purpose connector for pressure measurement and venting (Piece 8 in Fig. 1) at the high place (top) of the brake cylinder, with thread specification M16. When measuring pressure, remove the protective cap and connect the pressure measurement component; when venting, take down the anti-fall ring on the protective cap and then tighten the protective cap as shown in Fig. 4, and then return to the original state after venting.
No air venting status Air venting status
Contact Us
- Jiaozuo Hengyang Heavy Industry Brake Co.
brakes |
- Crane Brake High Quality DZ Series Drum Brake
- Yaw Brake Wind Mills Generator Use Brake DADH Series
- BYWZ4-300/45 Explosion-Proof Electro-Hydraulic Brake Suitable for Explosive Place
- YW-L Series Hydraulic Electric Drum Brake Crane Brake
- YW500 Series Industrial Brake Electric-Hydraulic Thruster Drum Brake
- Electric-Hydraulic Thruster Block Brake YW500 Series Industrial Brake
- High Quality Electric-Hydraulic Thruster Block Brake YWZ13-400/121 S2 Industrial Brake
- Electric Hydraulic Thruster Block Brake YWZ13-400/121 S2 Industrial Brake
- Electric Hydraulic Drum Thruster Brake YWZ13-300/50 S1 Industrial Brake
- Bridge Tower Crane Impeller Electric Hydraulic Drum Thruster Brake YWZ13-300/50 S1
- Bridge Tower Crane Impeller Electric Hydraulic Drum Brake YWZ9-400/121 Industrial Brake Factory Direct Supply Brake
- YWZ9-400/121 Crane Electric Hydraulic Drum Brake Industrial Brake Factory Direct Supply Brake
- Manufacturer Direct Supply Shoe Brake YWZ8-200/23 Electric Hydraulic Block Brake Industrial Brake
- YWZ8-200/23 Crane Electric Hydraulic Drum Brake Industrial Brake
- YWZ5-200/30 Crane Electric Hydraulic Drum Brake Industrial Brake Factory Direct Supply Brake
- High Quality Industrial Brake YWZ4-400/45 for Crane Industry
- Electric Hydraulic Block Brake Matched With Electric Hydraulic Thruster YWZ4-400/45 for Crane Industry
- YWZ4-200/30 Crane Electric Hydraulic Drum Brake Industrial Brake Factory Direct Supply
- YWZ4-200/30 Industrial Brake Crane Electric Hydraulic Drum Brake
- Factory Direct Supply YWZ3 Series Electric Hydraulic Block Brake
- YWZ3 Series Electric Hydraulic Block Brake
- Electric Hydraulic Block Brake Matched With Electric Hydraulic Thruster YWZ4-500/125 for Crane Industry
- YWZ4-500/125 Electric Hydraulic Block Brake Matched With Electric Hydraulic Thruster
- Manufacturer Supply YWZ2-800 Electric Hydraulic Block Brake Matched With Electric Hydraulic Thruster
Popular Searches
- electromagnetic brake
- Electromagnetic Clutch Brake
- Dc Electromagnetic Brake
- uniform hanger
- Clutch Brake
- magnetron microwave oven parts
- laundry system
- electro hydraulic thruster
- electromagnetic clutch and brake
- electromagnetic brake 24v
- armature plate
- automatic garment hanger
- air releaser
- armature stator parts
- floating plate
- ball hanger wood
Find Similar Products By Category
- Mechanical Parts & Fabrication Services > Industrial Brakes
- Buy on GoldSupplier.com
- How to Buy
- Browse by Catagories
- Browse by Hot Regoins
- Private Sourcing Events
- Sell on GoldSupplier.com
- How to Sell
- Post Products
- Manage Products
- Manage Groups
- Services
- Latest Sourcing Requests
- Product Update
- Companies of Today
- GoldSupplier.com Mobile Site
- B2B Articles
- About
- About Us
- Link to Us
- Contact Us
- Sitemap
- Please Enter your Email Address
- Please enter the content for your inquiry.
We will find the most reliable suppliers for you according to your description.
Send Now-
sales
Welcome to my shop! Glad to serve you!Please send your question!
Your message has exceeded the limit.
- Contact supplier for lowest price
- Customized Request
- Request Sample
- Request Free Catalogs
Your message has exceeded the limit.
-
-
Your inquiry content must be between 20 to 5000 characters.Send Now.
-
Please input the mailbox.
-