Contact Platform Support
Help CenterDS200PCCAG1ABB GE Spot Prompt Price Consultation Shall Prevail
Related Products
-
DS200RTBAG2AFB GE Gas Turbine Card Control System Communication (spot)US$ 100 - 260MOQ: 100 Pounds -
DS200SDCCG1AFD GE Drive Control Circuit Card (warranty and After-sales)US$ 100 - 200MOQ: 100 Pounds
-
DS200SDCCG1AGD DS200SDCCG5AHD GE Controller Module for Petrochemical and Natural GasUS$ 113 - 600MOQ: 100 Pounds
-
DS200SDCIG1ABA DS200SDCIG2AHB GE Power Module Controller Communication Module Available in StockUS$ 100 - 260MOQ: 100 Pounds
-
DS200SIOBH1AAA DS200SIOBH1ABA DS200SIOBH1ACA GE Main Control BoardUS$ 190 - 600MOQ: 100 Pounds
DS200PCCAG1ABB GE Spot prompt price consultation shall prevail
DS200PCCAG1ABB GE Spot prompt price consultation shall prevail
Our Email: 2235954483@qq.com
contact number:13313705507
contacts：HE
The GE DC Power Connect Board DS200PCCAG1ABB serves as an interface between the drive and the SCR power bridge. Static electricity can build up in the DS200PCCAG1ABB board and damage the board if guidelines are not adhered to that mitigate the static build up. For example, always wear a grounding strap when you handle, touch, or move the board. And before you install the board, keep it in the static-protective bag. Touch the bag to an unpainted metal surface and keep it against the surface for a few seconds.
If you happen to be replacing the board in cold dry weather take extra caution against static. You’ll find that static builds up easily in those weather conditions. And, always place the board on the package it came in. It protects against static and will prevent damage to the board. Have the package out and flattened if you need to put it down during installation.
Ribbon cables are flat wide cables that carry multiple signals from one device to another and are often used to carry signals on a board. However they tend to be delicate and require special handling instructions to prevent damage. The wires in ribbon cables are often thin and not designed for rough handling. When you disconnect a ribbon cable do not pull the connector out by pulling the ribbon cable. Instead, place you hand on the connector attached to the ribbon cable. Then disconnect by pulling the connector out of the connector on the board.
Send Inquiry to This Supplier
You May Also Like
-
DS200SLCCG1AFG GE Control Module Power Connector BoardUS$ 165 - 200MOQ: 100 Pounds
-
DS200TBOCG1AAA DS200TBQDG1AFF GE Module Gas Turbine Card Inventory Spare PartsUS$ 100 - 200MOQ: 100 Pounds
-
DS200TCCAG1BAA GE Gas Turbine Clamp of Gas Turbine SystemUS$ 165 - 260MOQ: 100 Pounds
-
DS200TCEAG1ACB GE Rst Extended Analog Terminal Filter ModuleUS$ 100 - 200MOQ: 100 Pounds
-
DS200TCEAG1BNE GE Communication Module Controller InventoryUS$ 100 - 200MOQ: 100 Pounds
-
DS200TCEBG1ACE GE Processor Motherboard Warranty After-sales Service WarehouseUS$ 100 - 260MOQ: 100 Pounds
-
DS200TCQCG1BGF GE Industrial Control Automation Gas Turbine ModuleUS$ 100 - 200MOQ: 100 Pounds
-
DS200TCQCG1BKG GE Unit Module Controller CardUS$ 100 - 200MOQ: 100 Pounds
-
DS200TCTGG1AFF GE Voltage Feedback Calibration BoardUS$ 190 - 200MOQ: 100 Pounds
-
DS215KLDCG1AZZ03A GE Module Gas Turbine Card Inventory Spare PartsUS$ 113 - 600MOQ: 100 Pounds
