Contact Platform Support
Help CenterModule Spare Parts PXI-4071
Related Products
-
Module Spare Parts PXI-8423US$ 1 - 100000MOQ: 1 Piece -
Module Spare Parts PXI-4351 185450D-01US$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts PXI-4461 186900T-11LUS$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts PXI-4462 188261H-11LUS$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts PXI-6527 185633D-01US$ 1 - 100000MOQ: 1 Piece
Focus on DCS, PLC, robot control system and large servo system.
Main products: various modules / cards, controllers, touch screens, servo drivers.
Advantages: supply of imported original products, professional production parts,
Fast delivery, accurate delivery time,
The main brands include ABB Bailey, Ge / fuanc, Foxboro, Invensys Triconex, Bently, A-B Rockwell, Emerson, ovation, Motorola, xyvom, Honeywell, Rexroth, KUKA, Ni, Deif, Yokogawa, Woodward, Ryan, Schneider, Yaskawa, Moog, prosoft and other brands
| PXI-4071 |
Stir thoroughly before using and occasionally during use. Read all label and Material Safety Data Sheet (MSDS) information prior to use. MSDS are available through our website or by calling 1-800-441-9695. USE WITH ADEQUATE VENTILATION. KEEP OUT OF REACH OF CHILDREN. Permissible temperatures during application: Temperature Range: 35ºF to 110ºF (air, surface, paint) (Optimum paint temperature 65-85ºF) Dew Point: Surface temperature must be at least 5ºF above the dew point. Relative Humidity: Maximum 85% New or Rework: Apply a liberal coat of WOOD GUARDIAN Penetrating Stain/Finish (Phenolic/Tung Oil) No. PP835. If the surface is highly porous, with the material striking in deeply, a second coat to fill the pores may be applied while the surface is still wet from the first coat. After the material has been on the surface several minutes, remove any puddles or material laying on the surface with squeegees or absorbent cloths. Buff with 00 steel wool when fully dry. Furniture: Apply a liberal first coat, wipe off excess and allow to fully dry. Alternately rag on a thin coat of material (allow it to dry), then buff using finer and finer steel wool or sandpaper until desired appearance is achieved. Stain: Apply a uniform penetrating coat of tinted product. Allow to dry thoroughly before varnishing suitable filler if necessary and sand smooth. OLD WOOD: Remove old coatings and weathered wood by pressure washing, power tooling or hand scraping and sanding as necessary to achieve a sound, absorbent bare wood surface. Sand smooth if necessary. CONCRETE FLOORS: To achieve a uniform appearance, acid etch the floor with muriatic acid (see Porter Technical Bulletin #14, ACID ETCHING CONCRETE). For a dust seal on un-etched concrete, clean thoroughly and allow the concrete to fully dry. REAPPLICATION ON WORN OR WEATHERED SURFACES: Apply test patches in several locations to be sure that the surface is open and porous enough for reapplication. Proceed if the test material strikes into the surface
Send Inquiry to This Supplier
You May Also Like
-
Module Spare Parts PXI-6608 185745H-02US$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts SCXI-1001US$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts SCXI-1102US$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts SCXI-1102BUS$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts SCXI-1104CUS$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts SCXI-1121US$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts SCXI-1140US$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts SCXI-1141 182610D-01US$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts REF542plus 1VCR007346 G0012US$ 1 - 100000MOQ: 1 Piece
-
Module Spare Parts REF615C-D HCFCACABANB2BAN1XDUS$ 1 - 100000MOQ: 1 Piece
