Contact Platform Support
Help CenterDECS-200-2L
Related Products
Brand:BASLER ELECTRIC
Type:DECS-200-2L
Origin: the United States
Warranty: 365 days
Colour: new/used
Shipping method: Courier delivery
Module of PLC, DCS, ESD system card, the card is a vibration monitoring system, steam turbine control system module, the advantages of the gas generator spare parts brand: Allen Bradley, BentlyNevada, ABB, Emerson Ovation, Honeywell DCS, Rockwell ICS Triplex, FOXBORO, Schneider PLC, GE Fanuc, Motorola, HIMA, TRICONEX, Prosoft etc. Various kinds of imported industrial parts
Our main products are widely used in metallurgy, petroleum, glass, aluminum manufacturing, petrochemical industry, coal mine, papermaking, printing, textile printing and dyeing, mechanical, electronic manufacturing, automobile manufacturing, plastic machinery, electric power, water conservancy, water treatment/environmental protection, boiler heating, energy, power transmission and distribution and so on.
Additional Features The 505E also provides the following features: First-Out Trip Indication (5 total trip inputs), Critical Speed Avoidance (2 speed bands), Auto Start Sequence (hot & cold starts), Dual Speed/Load Dynamics, Zero Speed Detection, Peak Speed Indication for Overspeed trip, and Isochronous Loadsharing between units. Using the 505E The 505E control has two normal operating modes, the Program Mode and the Run Mode. The Program Mode is used to select the options needed to configure the control to your specific turbine application. Once the control has been configured, the Program Mode is typically never again used, unless turbine options or operation changes. Once configured, the Run Mode is used to operate the turbine from start-up through shutdown. In Addition to the Program and Run modes, there is a Service Mode which can be used to enhance system operation while the unit is running. Refer to Volume 2 for information on the Service Mode. 505E Inputs and Outputs Control Inputs Two speed inputs which are jumper configurable for MPU (magnetic pickup units) inputs or proximity probes. Six analog inputs are available. One is dedicated as the extraction/admission input. The remaining five are configurable.
The sixth analog input has isolation circuitry and should be used for a self-powered signal that is not isolated. Sixteen contact inputs are available. Four are dedicated for shutdown, reset, raise speed setpoint, and lower speed setpoint. Another two contact inputs must be dedicated for generator breaker and utility tie breaker if the control is used in a generator application. Ten additional contact inputs can be configured. If the unit is not used in a generator application, then twelve additional contact inputs can be configured. Four function keys on the front panel of the control. F1 and F2 are dedicated to alarm and overspeed test, respectively. F3 and F4 can be used to enable or disable various functions of the control. Control Outputs Two actuator outputs with linearization curves for the HP and the LP valve outputs. Six 4–20 mA outputs, for meters or other readouts. Eight Form-C relay contact outputs, six that are configurable. The two dedicated relay outputs are for shutdown and alarm indication.
Send Inquiry to This Supplier
You May Also Like
-
TOSHIBA 2N3A8130-AUS$ 1039 - 2259MOQ: 1 Piece
-
STAHL ET-436-AT-R2-HB-TX-100GB-VUS$ 1040 - 2260MOQ: 1 Piece
-
ABSOLUTE MOX12-P3509 B 80026-173-23US$ 1043 - 2263MOQ: 1 Piece
-
EATON XV-440-10TVB-1-20US$ 1046 - 2266MOQ: 1 Piece
-
EATON MP3010US$ 1049 - 2268MOQ: 1 Piece
-
LAM 810-800082-043US$ 1061 - 2051MOQ: 1 Piece
-
S21260-SRSUS$ 1063 - 2052MOQ: 1 Piece
-
EATON XVS-430-10MPI-1-10US$ 1064 - 2053MOQ: 1 Piece
-
ATLAS TC-4000-SUS$ 1068 - 2059MOQ: 1 Piece
-
TPMC815-11US$ 1068 - 2059MOQ: 1 Piece
