AMLPP Filter Element RP095E10B STAUFF Import UF

"Analysis of common failures of air compressors

     The environment has poor ventilation and heat dissipation. There are three main situations in which the surrounding environment of the air compressor affects heat dissipation: one is that it is too close to a wall-like obstacle; the other is that there are other heat sources near the air compressor, and the third is that the front door and side door of the Ingersoll Rand air compressor parts are open during operation, and the fan Strong air currents cannot be formed.

(2) The radiator is blocked. When the surrounding environment of the air compressor is dusty, long-term operation will cause a layer of dust or sludge to adhere to the surface of the radiator, and the internal copper pipe is also easy to be blocked due to the accumulation of grease, which affects the heat dissipation effect.

(3) The oil filter is too dirty. This machine has 3 side-by-side oil filters. When they are too dirty, the resistance oil cannot enter the compressor at the normal flow rate, and the compressor will quickly heat up due to insufficient cooling and lubricating oil. When the pressure difference between the inlet and outlet oil exceeds 0.18MPa, the filter element needs to be replaced.

(4) The cooling oil level is too low. When the cold machine is checked, if the oil level is lower than the lower end of the inspection tube, it should be replenished immediately.

(5) Low oil mark or poor oil quality. The machine uses the manufacturer’s special compressor oil. When other low-grade or inferior oils are used, the viscosity and specific heat will not reach the standard and the temperature will be too high.

(6) The fan tape is broken or loose. When the tape breaks, the air compressor will automatically stop when the temperature is too high after running for about 5 minutes. If the tape is too loose, it will slip, which will reduce the fan speed and affect heat dissipation. At this time, the tightness of the fan tape should be replaced or adjusted.

(7) The oil shutoff valve is out of order. There is an oil cutoff valve between the oil filter and the compressor. When the oil cutoff valve cannot be opened, due to no oil lubrication and cooling, the temperature of the compressor rises rapidly after starting, and it will automatically stop after about 1min. Remove the temperature plug at the exhaust end of the compressor, you will find that the plug is dry and oil-free, and blue smoke will flow out of the hole. Open the maintenance hole at the bottom of the air compressor, remove the oil shut-off valve, and gently move the valve stem with your fingers to see if it can be pushed forwards and backwards and can be easily reset. If it is difficult to move or return, you need to further disassemble the oil shut-off valve. If there is grease on the valve stem or valve hole, it needs to be polished with fine sandpaper until it can slide easily; if the spring is broken or there is a foreign object stuck in the letter, it will also affect the movement of the valve stem. At this time, you need to replace the spring or clean the spring and spring seat.

(8) The filter element of the oil and gas separator is too dirty. When it is too dirty, the oil will affect circulation due to excessive resistance, causing overheating and shutdown. This situation is judged from the pressure difference before and after loading. When the pressure difference between the two ends is 3 times the initial pressure or the maximum pressure difference reaches 0.1 MPa, it should be cleaned or replaced.

(9) The thermostat bypass valve is in the open position. The thermostat bypass valve is in the open position when the machine is cold, and gradually closes when the temperature rises. When it fails, it may always be in the open position, and the cooling oil flows directly back to the air compressor from here without passing through the radiator, so the temperature will slowly rise and stop. The maintenance method is similar to that of the shut-off valve.

(10) Exhaust pressure is too high. When the exhaust pressure exceeds the rated 12MPa, the compressor and diesel engine will heat up and stop automatically when the compressor and diesel engine are overloaded for a long time. At this time, first check and adjust the pressure valve, and then check the diesel engine throttle control system and eliminate this fault. "

amlpp0215@gmail.com  /  Shanghai Amlpp Co., Ltd

Wechat : shamlpp

RP085E10B STAUFF Induced draft fan oil station filter

RP085E10V STAUFF Blower oil station filter element

RP095E10B STAUFF filter element

RP095E10V STAUFF Induced draft fan oil station filter

RP115E10V STAUFF Separate filter element

RP075E10B STAUFF Separate filter element

RP075E10V STAUFF Small oil station filter

RP085E20B STAUFF Mahle hydraulic filter

RP085E20V STAUFF Steam turbine filter element

RP095E20B STAUFF Power Plant EP

RP095E20V STAUFF Power filter

RP115E20B STAUFF Hydraulic oil return filter

RP115E20V STAUFF Anti-fuel filter

RP075E20B STAUFF Separate filter element

RP075E20V STAUFF Oil station filter element of slag conveyor drive device

RP085E05B STAUFF High pressure oil filter

RP085E05V STAUFF In addition to impurities

RP085E05V STAUFF Haqi fine filter

RP095E05B STAUFF Fuel-resistant cellulose filter

RP095E05V STAUFF Return oil filter element

RP115E05B STAUFF PALL main pump

RP115E05V STAUFF Regeneration pump inlet filter, slurry circulating pump reducer filter

RP075E05B STAUFF Small machine adjustment oil filter

RP075E05V STAUFF Main oil pump outlet filter element

RP085E03B STAUFF Oil motive filter element

RP085E03V STAUFF Coupler filter

RP095E03B STAUFF Outlet filter element of jack shaft oil pump

RP095E03V STAUFF Oil motive filter element

RP115E03B STAUFF Pressurized air motorized fuel transfer station filter element

RP115E03V STAUFF Power plant oil motive filter element

RP075E03B STAUFF Oil filter

RP075E03V STAUFF High efficiency filter element of oil filter

RP085E10B STAUFF EH Regeneration System Cellulose

RP085E10V STAUFF Diatomite filter

RP095E10B STAUFF Import UF

RP095E10V STAUFF Hydraulic filter

RP115E10B STAUFF Pal

RP115E10V STAUFF Working oil filter

RP075E10B STAUFF Stainless steel coal machine filter

RP075E10V STAUFF Oil station filter element of slag conveyor tensioning device

RP085E20B STAUFF Degreasing filter element

RP085E20V STAUFF Small machine adjustment oil filter

RP095E20B STAUFF Small machine lubricating oil filter

RP095E20V STAUFF Oil return filter element

RP115E20B STAUFF Power plant oil filter

RP115E20V STAUFF Power plant lubrication system filter element

RP075E20B STAUFF Main engine EH oil system

RP075E20V STAUFF high pressure filter

SF6610 STAUFF Lubrication system filter element

SF6611 STAUFF Xinhua Oil Station Hydraulic Filter

SF6606 STAUFF Stainless steel oil return filter element

SF6607 STAUFF Dongqi filter

SF6603 STAUFF Fuel tank fine filter

SF6604 STAUFF Coal pulverizer filter element

SF6720 STAUFF Rexroth high pressure filter

SF6710 STAUFF Top shaft oil pump filter element

SF6711 STAUFF Emerald filter

SF6706MG STAUFF Pre-pump filter element

SF6707MG STAUFF Fine filter

SF6703MG STAUFF Regeneration fine filter

SF6704MG STAUFF Rexroth high pressure filter

SF6726MG STAUFF Coalescing filter

SP200E05B STAUFF High pressure pa

SP200E05V STAUFF Top shaft oil pump inlet filter element

SP300E05B STAUFF EH system pump suction