| Motor type | Output Power | Voltage | Load | Speed | Rated Torque | Efficiency | Noise | IP Class |
| KW | V | A | RPM | Nm | % | dB | ||
| VOL- IEC90S2250-2P | 2.25 | 220 ac | 6.42 | 3000 | 7.16 | 92 | 62 | IP 54 |
| VOL- IEC100S2250-4P | 2.25 | 220 ac | 6.42 | 1500 | 14.33 | 92 | 62 | IP 54 |
| VOL- IEC112S2250-6P | 2.25 | 220 ac | 6.42 | 1000 | 21.48 | 92 | 62 | IP 54 |
| VOL- IEC112S3750-2P | 3.75 | 220 ac | 10.70 | 3000 | 11.94 | 92.5 | 62 | IP 54 |
| VOL- IEC112S3750-4P | 3.75 | 220 ac | 10.70 | 1500 | 23.88 | 92.5 | 62 | IP 54 |
VIEW MORE PLS CONTACT US >>>



Q:Motor has been running then fails to start,what to do?
A:Likely cause: Fuse or circuit breaker is tripped.
What to do: Replace the fuse or reset the breaker.
Likely cause: Armature is shorted. Motor may make a humming noise and the circuit breaker or fuse will trip.
What to do: Disassemble motor and inspect the armature for a burnt coil. Inspect the commutator for burnt bars. If this condition exists, the motor needs to be replaced.
Likely cause: The brushes may be worn down too far and no longer make contact with the commutator.
What to do: Check the brushes to make sure that they are still making contact with the commutator. Contact manufacturer for brushes.
Likely cause: Controller may be defective.
What to do: Verify voltage is coming out of the controller.
Q: On initial installation, motor fails to start up,what to do?
A: Likely cause: Motor is incorrectly wired
What to do: Verify that the motor is wired correctly.
Likely cause: No output power from controller.
What to do: Measure voltage coming from the controller.
Likely cause: Motor is damaged and the armature is rubbing against the magnets.
What to do: Disassemble motor and see if the armature can be realigned by reassembly. Motor may have to be replaced.
Q: Motor takes too long to accelerate,what to do?
A: Likely cause: Motor controller not properly set.
What to do: Adjust the acceleration trim pot of the controller.
Likely cause: Brushes are worn.
What to do: Verify brush length.
Likely cause: Bearings may be defective.
What to do: Inspect bearings. Noisy or rough bearings should be replaced.
Q: Motor runs in the wrong direction,what to do?
A: Likely cause: Incorrect wiring
What to do: Interchange the two motor leads.
Q: Motor runs OK but has a clicking noise,what to do?
A: Likely cause: Suspect a burr on the commutator.
What to do: Remove burr from commutator using a commutator stone.
Send Inquiry to This Supplier
You May Also Like
-
Baby Doll Stroller312x52-250US$ 1 - 10MOQ: 1000 Pieces
-
Electric Bicycles Parts ProcessingUS$ 1 - 100MOQ: 1 Piece
-
China OEM Competitive Price E-bike Spare PartsUS$ 0.01 - 100MOQ: 50 Pieces
-
LCD Display 26'' 48V 1000W Electric Bike Conversion KitsUS$ 330 - 350MOQ: 10 Sets
-
2015custom Coil for Torque Sensor of Mountain BikeUS$ 0.2 - 1.5MOQ: 1000 Pieces
-
CE Approved Electric Bicycle Parts 100W Motor Controller for Drift TrikeNegotiableMOQ: 2000 Pieces
-
Carbon Brush for Mobility Scooter Carbon Brushes for MotorUS$ 0.20 - 1.00MOQ: 500 Pieces
-
4G Battery Monitoring and Positioning Terminal 4G/5G Wireless Communication Core Board Development BoardUS$ 21 - 28MOQ: 1 Piece
-
Throttle FP-6 Style 0-5K Foot Throttle for Curtis EV Potentiometer Type 0-5 Ohm With 7 Cables PlugNegotiableMOQ: 1
-
Electric Starter E Bike Motor For 90Cc 110Cc 125Cc 4-Stroke Quad Atv UtvNegotiableMOQ: 1








