Ship Rubber Airbag for Launching
US$ 500 - 1200
/ Piece
1 Piece(Min. Order)
- Qingdao Port
- T/T L/C
You May Like
Product Details
Brand Name | FLORESCENCE | Place of Origin | China | |
Model Number | FL-SJY1650 | Part | Other, Ship rubber airbag for launching |
Product Description
Ship rubber airbag for launching
Florescence ship rubber airbags can be used to launch and land a ship up to 100,000DWT. Comparing to the traditional slipway launching method, the ship rubber airbags are much convenient, because ship airbag can launch a ship at any seaside, so there's no need to worry about the construction of launching facilities; besides, the marine airbag need little maintenance and can be used repeatedly. Need no more than air compressors, winches and ropes.
How to choose airbag size?
Before to provide suitable airbag size and quantity for your ship, please provide below information:
1.Ship length,width and weight.
2.Type of ground ship is built on? (Dirt, concrete, etc.)
3.Type of ship?
4.Depth in meters of the water where the ship first enters the water?
5.What's the angle degree of slipway? (Land, not under water)
6.Please provide the low/high tide schedule at site.
7.The working height? (The block stand height under the ship)
8.Distance from bottom of propeller to the water level?
9.Distance from back of ship (in dry dock) to the water entry point?
*If possible, please provide photos of the launch area.
1.Ship length,width and weight.
2.Type of ground ship is built on? (Dirt, concrete, etc.)
3.Type of ship?
4.Depth in meters of the water where the ship first enters the water?
5.What's the angle degree of slipway? (Land, not under water)
6.Please provide the low/high tide schedule at site.
7.The working height? (The block stand height under the ship)
8.Distance from bottom of propeller to the water level?
9.Distance from back of ship (in dry dock) to the water entry point?
*If possible, please provide photos of the launch area.
Ship launching procedure
Procedure of Launch a ship by rubber airbags
1.Pre launch preparation work for shipyard
Slipway Enhancement
Water survey
Ground anchor
Seal thruster holes if there are.
2.Basic equipment needed for ship launching
Rigging equipment:Winch,Pulley,Swivel,Lug,Shackle,Wire sling,Ground Anchor
Inflate equipment: Air Compressor, Inflating Pipe
Airbag moving equipment: Forklift, mobile crane
3.Crew preparation
4.Rigging Arrangements
5.Lifting the blocks
6.Move vessel forward
7.Vessel Launching
1.Pre launch preparation work for shipyard
Slipway Enhancement
Water survey
Ground anchor
Seal thruster holes if there are.
2.Basic equipment needed for ship launching
Rigging equipment:Winch,Pulley,Swivel,Lug,Shackle,Wire sling,Ground Anchor
Inflate equipment: Air Compressor, Inflating Pipe
Airbag moving equipment: Forklift, mobile crane
3.Crew preparation
4.Rigging Arrangements
5.Lifting the blocks
6.Move vessel forward
7.Vessel Launching
Advantages of ship rubber airbag
Different airbag size stock available, quick delivery
Provide repair kit and on site instruction
Long time service life can be reused many times
Wear resistance and anti aging
Good raw material and cord fabric
Do no harm to the environment. Time & money saving
Need no more than air compressors, winches and ropes
Marine airbags are much cheaper and portable than other methods
Provide repair kit and on site instruction
Long time service life can be reused many times
Wear resistance and anti aging
Good raw material and cord fabric
Do no harm to the environment. Time & money saving
Need no more than air compressors, winches and ropes
Marine airbags are much cheaper and portable than other methods
Acceptance test for ship rubber airbag
Our test the ship rubber airbags purchased based on the test items indicated below:
* The appearance of the airbag is free from defects such as blemishes, bubbles, cracks, etc.
* The diameter, length and working pressure of each air bag need to be tested before shipping.
* The airtightness test of the airbag complies with the ISO 14409 standard. Air loss per hour does not exceed 5%
* The appearance of the airbag is free from defects such as blemishes, bubbles, cracks, etc.
* The diameter, length and working pressure of each air bag need to be tested before shipping.
* The airtightness test of the airbag complies with the ISO 14409 standard. Air loss per hour does not exceed 5%
Application of ship rubber airbag
1. Ship launching, lifting and refloating
2. Floating bridge and dock construction
3. Rescue and remove of wrecked ship
4. Setting up temporary pontoon bridge pier and water transport channel
5. Blocking debacle of anti-flood and anti typhoon dam
6. Applying to short distance transport of the bridge, concrete piers, drilling equipment
2. Floating bridge and dock construction
3. Rescue and remove of wrecked ship
4. Setting up temporary pontoon bridge pier and water transport channel
5. Blocking debacle of anti-flood and anti typhoon dam
6. Applying to short distance transport of the bridge, concrete piers, drilling equipment
Safety precaution of ship rubber airbag
1.Over pressure Control:
Strictly control the operating pressure, over pressure is forbidden.
2.The Landing Slipway Requirements:
The landing ground should be ground or cement concrete, according the tonnage of different ships.
3.Avoid Sharp Objects(most important):
Make sure no sharp objects and smooth & clean ground during using airbags in case of any break.
4.Avoid Distortion And Overweight:
Avoid distortion in the length direction during rolling and avoid overweight load after gas charging.
Strictly control the operating pressure, over pressure is forbidden.
2.The Landing Slipway Requirements:
The landing ground should be ground or cement concrete, according the tonnage of different ships.
3.Avoid Sharp Objects(most important):
Make sure no sharp objects and smooth & clean ground during using airbags in case of any break.
4.Avoid Distortion And Overweight:
Avoid distortion in the length direction during rolling and avoid overweight load after gas charging.
Storage of ship rubber airbag
1.Ship rubber airbag should be maintained in a dry ventilated room and be protected from light.
2.Ship rubber airbag should be in a relaxed condition free from tension, compression or other deformation.
3.Ship rubber airbag should be kept away from any heat source.
4.Ship rubber airbag should be protected from acids, alkalis, oils or organic solvents.
2.Ship rubber airbag should be in a relaxed condition free from tension, compression or other deformation.
3.Ship rubber airbag should be kept away from any heat source.
4.Ship rubber airbag should be protected from acids, alkalis, oils or organic solvents.
Packing and delivery
Contact Us
- Qingdao Florescence Rubber Products Co.,Ltd
Product Categories
Pneumatic fender | Airbag | foam filled fender | Rubber fender |
Oil boom |
New Products
-
Ship Floating Fender With Aircraft Tyres
-
Dia2.5m L5.0m Oil Tanker Floating Pneumatic Fender
-
BV Certificated Pneumatic Rubber Fender For Dock
-
Pneumatic Fender for STS Service
-
Oil Tanker Berthing Ship Floating Fender for Marine Service
-
Boat Marine Ship Floating Fender to Singapore
-
Cylindrical Rubber Fender
-
Marine Tugboat Cylindrical Rubber Fender
-
Dock Cylindrical Rubber Fender for Berthing
-
Boat Marine Wharf Fender Cylindrical Rubber Fender
-
Cylindrical Fender Dock Ship Rubber Fender
-
Boat Marine Cylindrical Rubber Fender
Popular Searches
- inflatable balloon
- pontoon
- air bag
- floating pontoon
- marine airbag
- rubber balloon
- inflatable airbag
- marine rubber airbag
- ship launching airbag
- pneumatic rubber airbag
- floating airbag
- pneumatic rubber
- lift airbag
- lifting airbag
- marine balloon
- salvage airbag
- air bladder
- inflatable rubber mandrel
- rubber pontoon
- ship launching marine rubber airbag
- rubber balloon airbag
- natural rubber airbag
- inflatable balloon
- natural rubber
- rubber bumper
- pontoon
- air bag
- marine airbag
- vacuum pouch
- rubber airbag
Recommended Products
- Caterpillar Gas Engine G3608 G3606 Pipe 4W-7322
- Remanufactured Cylinder Head for CAT C27 C32 Engines
- For CAT High Quality 4226493 422-6493 Air Compressor for 305/306 Small Excavators
- for Vogel Paver 2100-3 96.2951.1000 054808 Hydraulic Gear Pump 9629511000 Gear Pump
- CAT Original Gasket 7E-3478
- Perkins Engine 404D-22 404D-22T Electronic Speed Controller T434827, U85186160
- Wilson P550E3 Generator Set Perkins 2506 Starter Motor CH12807
- Advantages of Cummins QSK45 Engine Supply
- CAT Grade Control Grader 140GC 120GC Drive Shaft 597-0843
- CAT PERKINS Engine C18 2806 Turbocharger T403095, 358-4920
- C15 C18 2506 2806 Engine Particle Trap T402574, 390-0645
- Caterpillar 120H Grader Oil Pressure Control Valve 107-0543 CAT Original Parts
Find Similar Products By Category
- Industrial Equipment & Components > Engine & Part > Engine Parts
- Please Enter your Email Address
- Please enter the content for your inquiry.
We will find the most reliable suppliers for you according to your description.
Send Now
Qingdao Florescence Rubber Products Co.,Ltd
AIBot OnlineThis conversation is AI-generated. Contact manufacturer before transaction to confirm info.
-
sales
Hi there! Welcome to my shop. Let me know if you have any questions.
Your message has exceeded the limit.

- Contact supplier for lowest price
- Customized Request
- Request Sample
- Request Free Catalogs
Your message has exceeded the limit.
-
Purchase Quantity
-
*Sourcing Details
Your inquiry content must be between 10 to 5000 characters.
-
*Email
Please enter Your valid email address.
-
Mobile