Contact Platform Support
Help Center7HL CiTiceL Electrochemical Hydrogen Chloride Gas Sensor (HCl Sensor)
Related Products
-
The GS Oxygen Sensor KE Series (KE-25 & KE-50)NegotiableMOQ: 1 Piece -
Compact CO Sensor TGS5141 for the Detection of Carbon MonoxideUS$ 1 - 1MOQ: 1 Piece
-
TGS5042 Carbon Monoxide Sensor CO SensorUS$ 8 - 12MOQ: 1 Piece
-
Figaro Oxygen Sensor SK-25FNegotiableMOQ: 1 Piece
-
O2I-Flex Oxygen Sensor Interface BoardNegotiableMOQ: 1 Piece
7HL CiTiceL Hydrogen Chloride Sensor (HCl Sensor) Key Features & Benefits:
• Robust, industry standard 7-Series packaging
• Compact Size
7HL CiTiceL Hydrogen Chloride Sensor (HCl Sensor) Technical Specifications
| MEASUREMENT | |
| Operating Principle | 3-electrode electrochemical |
| Measurement Range | 0-50 ppm HCl |
| Maximum Overload | 100 ppm HCl |
| Filter | None |
| Sensitivity* | 0.75 ± 0.25 µA/ppm |
| Response Time (T90)* | |
| Baseline Offset (clean air)* | 0 to +2 ppm HCl equivalent |
| Zero Shift (+20°C to +40°C) | |
| Resolution | 0.5 ppm (when used with recommended electronics) |
| Repeatability | 2% of signal |
| Linearity | Linear |
| ELECTRICAL | |
| Recommended Load Resistor | 33 Ω |
| Bias Voltage | +300 mV |
| MECHANICAL | |
| Weight | 17 g |
| Housing Material: | |
| Cap | Polycarbonate |
| Body | ABS |
| Orientation | Any |
| ENVIRONMENTAL | |
| Operating Temperature Range | -20°C to +50°C |
| Recommended Storage Temp | 0°C to 20°C |
| Operating Pressure Range | Atmospheric ± 10% |
| Operating Humidity Range | 15 - 90% RH non-condensing |
| LIFETIME | |
| Long Term Sensitivity Drift | |
| Expected Operating Life | Two years in air |
| Storage Life | 6 months in CTL container |
* Specifications are valid at 20°C, 50% RH and 1013 mBar, using City Technology recommended circuitry. Performance characteristics outline the performance of sensors supplied within the first 3 months. Output signal can drift below the lower limit over time.
Poisoning
CiTiceLs are designed for operation in a wide range of environments and harsh conditions. However, it is important that exposure to high concentrations of solvent vapours is avoided, both during storage, fitting into instruments and operation.
When using sensors with printed circuit boards (PCBs), degreasing agents should be used before the sensor is fitted. Do not glue directly on or near the CiTiceL as the solvent may cause crazing of the plastic.
Send Inquiry to This Supplier
You May Also Like
-
TGS2600 Air Quality Sensor for The Detection of Air ContaminantsUS$ 3.5 - 5MOQ: 1 Piece
-
TGS2602 - For The Detection of Air ContaminantsUS$ 1 - 1MOQ: 1 Piece
-
TGS2603 Air Quality Sensor For Detection of Odor and Air ContaminantsNegotiableMOQ: 1 Piece
-
Electrochemical O2 Gas Sensor Oxygen Sensor O2-A2US$ 1 - 1MOQ: 1 Piece
-
TGS2620 - For The Detection of Solvent VaporsUS$ 1 - 1MOQ: 1 Piece
-
LuminOx Fluorescence-based Optical Oxygen O2 Sensor LOX-02US$ 60 - 70MOQ: 1 Piece
-
Individual Sensor Board (ISB) Alphasense B4 4-Electrode Gas SensorsUS$ 1 - 1MOQ: 1 Piece
-
CGM6812-B00 Pre-calibrated Combustible Gas Sensor ModuleNegotiableMOQ: 1 Piece
-
NGM2611-E13 Pre-calibrated Methane Sensor ModuleNegotiableMOQ: 1 Piece
-
OPC-N2 PM2.5 Particle SensorUS$ 600 - 650MOQ: 1 Piece
