NEW FACTORY SEAL 10201/2/1 Honeywell Dcs

Contact name:Sandy Lin

Whatsapp/skype/Phone number:86-18020776786

Email:unity@mvme.cn

With oil prices of $100 a barrel or more, even more difficult-to-access sources have become economically viable. Such sources include tar sands in Venezuela and Canada, shale oil and gas in the US (and developing elsewhere), coal bed methane and synthetic diesel (syndiesel) from natural gas, and biodiesel and bioethanol from biological sources have seen a dramatic increase over the last ten years. These sources may eventually more than triple the potential reserves of hydrocarbon fuels. Beyond that, there are even more exotic sources, such as methane hydrates, that some experts claim can double available resources once more.

 About Macro Keys The “A”, “B”, “C” or “D” keys can be used to automatically activate a series of commands of up to 16 keystrokes, if programmed for this function. These keystrokes, as a group, are called “macros” and are stored in the system's memory. • Typical macro functions can include: - Arming sequences: STAY, NIGHT-STAY, INSTANT, or AWAY - Bypassing particular zone(s) - Activating relay(s) for turning on (or off) lights, fans, etc. • Up to four macros can be assigned – but no more than one macro to a key. • Macros can be activated only by users with authority levels authorized to perform the macro’s function. NOTE: The installer must activate the desired function key (using *57 Function key Menu Mode) before macros can be assigned. See the chart at the back of this manual for the key(s) assigned for macros. 1. + [#] + [6] + [6] (Master Code) Alpha Display: ∗∗∗∗DISARMED∗∗∗∗ READY TO ARM 2. Enter the macro number (1-4) to be programmed at the “Select Macro?” prompt. Remember, only one macro can be assigned to each key. SELECT MACRO 1-4 0 3. If a macro has been previously defined, the keystrokes are shown on the bottom line of the display; otherwise the display is blank. To exit this mode (and keep the existing macro definition), press any key except the [∗] key. The system returns to normal mode. To define a macro for the selected key, press [∗] and continue with the next prompt. MACRO DISPLAY Enter the first of the series of desired commands, (do not include your master code), then press/hold the “D” key for at least two seconds to complete the first command. This key terminates each command, and appears as an “F” in the keypad display

11098780

 COMAU 19010127

 COMAU PS101

 FUJI CPS-10FB

 GE FANUC A03B-0807-C161

 GMF ROBOTICS IE-0404-010-001

 GMF ROBOTICS IE-0404-030-003

 HIRATA H-3335

 HIRATA HPC-700B

 HIRATA HPC-703

 HIRATA HPC-709

 HIRATA HPC-723A

 HIRATA HPC-725

 HIRATA HPC-747

 HIRATA HPC-747A

 HIRATA HPC-767C

 HITACHI LQE020

 HITACHI LQE050

 HITACHI LQP010

 HITACHI LQV000

 HOBART 362732

 IDEC MK1234-21

 INDRAMAT HDS03.2-W075N-HS45-01-FW

 ISI ROBOTICS A6A07-1I

 ISI ROBOTICS A6A46-1I

 ISI ROBOTICS A6A47-1I

 ISI ROBOTICS A6A66-1I

 ISI ROBOTICS A6A72-1I

 ISI ROBOTICS AD-5678

 KAWASAKI 1HY-31

 KAWASAKI 1HZ-50

 KAWASAKI 50607-1088

 KAWASAKI 50607-1090

 KAWASAKI 50607-1091

 KAWASAKI 50607-1133

 KAWASAKI 50630-1049

 KAWASAKI 50817-1045

 KAWASAKI 50817-1133

 KAWASAKI 50817-1182

 KAWASAKI 50817-1220

 KAWASAKI 50817-1260

 KAWASAKI 50999-1049

 KAWASAKI 50999-1548

 KAWASAKI 50999-1557

 KAWASAKI 50999-1692

 KAWASAKI 50999-1702

 KAWASAKI 50999-1760

 KAWASAKI 50999-1769

 KAWASAKI 50999-1859

 KAWASAKI 50999-1860

 KAWASAKI 50999-1914

 KAWASAKI 50999-2143

 KAWASAKI 50999-2145

 KAWASAKI 50999-2206

 KAWASAKI 50999-2383

 KAWASAKI 9EA-31

 KAWASAKI 9EC-33

 KAWASAKI 9ED-33

 KAWASAKI 9ED-34

 KAWASAKI 9EH-32

 KAWASAKI 9EL-32

 KAWASAKI 9MH-32

 KAWASAKI 9SV-31

 KAWASAKI 9TQ30

 KAWASAKI A030065B

 KAWASAKI A100220B

 KUKA KPS-600/20-REL

 KUKA KSD1-48

 KUKA PM6-600

 MITSUBISHI A1SD71-MOTION

 MOTOMAN JANCD-10O3E

 MOTOMAN JANCD-HA03

 MOTOMAN JANCD-MFC05

 MOTOMAN JANCD-MM13-00

 MOTOMAN JANCD-SV02C

 MOTOMAN JZNC-RK41-2

 MOTOMAN JZNC-RK41-3

 MOTOMAN JZNC-TU58

 NACHI 21-90102748

 NACHI AR52-KUNIT-01