Long Range Transmit Distance Integrated PCBA rf Module CC1110 rf Module

General Description

The VT-CC1110-433M RF Data Transceiver Module is a low-power, highly integrated UHF transceiver, combines RF transceiver with MCU, designed for long-range wireless data transceiver applications.

Key Features

Radio

·High receiving sensitivity, -110dBm at 1.2kBand

·Programmable output power up to 10dBm,

transmission distance reach more than 200m

·433MHz transceiver, customaries for

315/433/868/915MHz

·Support FSK, GFSK, ASK/OOK and MSK modulation

·Programmable data rate from 1.2kBand to 500kBand

·Digital RSSI / LQI support

8051 MCU

·Powerful DMA functionality

·32KB in-system programmable flash and 4KB RAM

·128-bit AES security coprocessor

·7-12 bit ADC with up to eight input

·Two USARTs and one I2S

·16 bit timer with DSM model

·Three 8 bit timers

·12 GPIO pins

·Hardware debug support

General

·12 GPIO pins offer to user

·Supply voltage range 2.0-3.6V

·Small package size 22.0*20.0mm

Applications

·Low-power wireless Soc applications

·Wireless alarm and security systems

·Industrial monitoring and control

·Wireless sensor network

·AMR-Automatic Meter Reading

·Home and building automation

Electrical Characteristics

Ta = 25°C, VCC = 3.3V

TEST ITEM TEST CRITERIA & REQUIREMENT REMARKS

Voltage supply 2.0~3.6V DC

Center frequency 433MHz Programmable

Frequency error ±10KHz

Modulation 2-FSK/GFSK/ASK/OOK/MSK Programmable

Output power Up to 10dBm Max: 10 dBm

Receiving sensitivity -110dBm @1.2 kBand

Receiving current <22mA @1.2kBand

Transmitting current <35mA Po=10dBm

Sleep consumption 3uA

Data rate 1.2-500kBand programmable

Bandwidth 58-650kHz 26MHz ctystal

Transmit distance 200m 10kBand @ open area

Antenna 50ohm

Store temperature -50~150°C

Operating temperature -20~75 °C Temperature below -20°C are customized

Package size 22.0*20.0mm

Typically, equipment utilizing this device requires emissions testing and government approval, which is the responsibility of the equipment manufacture.

Package Description

Pin Description

Pin name Pin type Description

VCC Power DC 2.0-3.6V

GND Ground GND

RESET reset CC1110 RESET, read CC1110 datasheet for detail

P0.0 Digital I/O CC1110 P0.0, read CC1110 datasheet for detail

P0.1 Digital I/O CC1110 P0.1, read CC1110 datasheet for detail

P0.2 Digital I/O CC1110 P0.2, read CC1110 datasheet for detail

P0.3 Digital I/O CC1110 P0.3, read CC1110 datasheet for detail

P0.4 Digital I/O CC1110 P0.4, read CC1110 datasheet for detail

P0.5 Digital I/O CC1110 P0.5, read CC1110 datasheet for detail

P1.2 Digital I/O CC1110 P1.2, read CC1110 datasheet for detail

P1.3 Digital I/O CC1110 P1.3, read CC1110 datasheet for detail

P1.4 Digital I/O CC1110 P1.4, read CC1110 datasheet for detail

P1.5 Digital I/O CC1110 P1.5, read CC1110 datasheet for detail

P2.1 Digital I/O CC1110 P2.1, read CC1110 datasheet for detail

P2.2 Digital I/O CC1110 P2.2, read CC1110 datasheet for detail

ANT Antenna interface 50ohm

Read datasheet of the CC1110 for more information.

Questions and Answers

Description Reason and Solution

Can’t communication 1.The power supply connect not well, check the module VCC whether it is out of maximum rating.

2.The signal line connect not well, check the module SPI interface.

3.The settings of the transmitter module and receiver module are not the same. Check these modules’ register configuration.

4.Signal block. If the transmitter work with a high TX power, and the receiver was put at a short distance(<0.5m), maybe there is a signal block to make no communication.

Communication distance is too short 1.The application environment is too bad or the antenna is shield. Put the antenna to a better place outside or higher throw a coaxial line , replace it with a higher gain antenna.

2.The work space contains a same frequency interference source, or a strong magnetic field interference, power source disturbance. Try to change the carrier frequency or get far away from the source of the disturbance.

3.The power supply is not strong. Check the voltage and the current whether it is enough.

High data error 1.The power supply ripple is too big, Change the power supply.

2.Check the module register configuration, it is recommended to set as the CC1110-datasheet.

3.There is a carrier frequency interference, change the channel.

4.The antenna unmatched to the module RF interface, change another matched antenna.