600W constant voltage 12V led power supply high power led drivers

Item No.

NS-200W-12V

NS-250W-12V 

NS-600W-5V 

NS-200W-24V 

NS-600W-12V 

NS-600W-24V 

Output 

DC Voltage 

12V 

 12V

5V 

24V 

 12V

24V 

Rated Current 

16.5A

21A 

40A 

8.3A 

50A 

25A

Current Range 

0~16.5A 

0~21A 

0~40A 

0~8.3A 

0~50A 

0~25A

Rated Power 

200W 

250W 

600W 

 200W

600W 

600W 

Ripple & Noise (Max) Note 2 

175mVp-p 

 195mVp-p 

165mVp-p 

235mVP-p 

125mVp-p 

150mVp-p 

Voltage Tolerance Note 3

±1%

±1.0% 

Line Regulation 

±0.5%

±0.2% 

±0.5% 

±0.2% 

±0.6% 

±0.5% 

Load Regulation 

±0.2% 

±0.5% 

±0.5% 

 ±0.2%

±0.6%

±1.0 %

Set up time,Hold time

  200ms, 800ms,1000ms,50ms,20ms at full load

 Input

 Voltage Range Note. 4

90~250VAC;100~250VAC  vary by switch

Frequency Range 

47~63Hz 

 Efficiency (Type.)

82% 

82% 

80% 

80% 

82% 

78% 

 AC Current (Type.)

3.15A/115VAC 1.5A/230VAC 

 Inrush Current (Max)

Leakage Current 

<3.5mA / 240 VAC 

Protection 

Over Load 

105 ~ 150% rated output power 

Protection short circuit shut down o/p voltage, re-power on to recover

Over Voltage 

13.8~16.2V 

 13.8 ~16.2V

5.75  ~6.95V

27.6 ~ 32.4V 

 27.8~32.6V

15.6v ~ 18.2V 

Protection type: Shut down o/p voltage, re-power on to recover 

Environment 

Working Temperature 

-30 ~ 70°c 

Working Humidity 

20 ~ 90% RH non-condensing 

Storage temp & Humidity 

-40~+80°c,10~95%RH 

Temp. coefficient 

±0.03/ºc (0~50°c) 

Vibration 

10 ~ 500Hz,2G 10min/1cycle,period for 60min,each along X,Y,Z axes 

Safety and EMC 

 Safety Standards

IP42 approved 

Withstand Voltage 

I/P-O/P,I/P-FG,O/P-FG:100M Ohms/500vdc

Isolation Resistance 

I/P-O/P,I/P-FG:100M OHMS/500VDC

EMC Emission 

Compilance to EN61000-4-2,3,4,5,6,8,11,ENV50204,EN55024,light industry level, criteria A

EMC Immunity 

Comply with EN55022 class B, EN61000-3-2 class A (≤80% load), EN 61000-3-3 

Others

MTBF 

703Khrs min, MIL-HDBK-217F (25ºC) 

Remark:

1.All technical data if not mentioned, it should be measured at 230v,rated load and 25 °c of relative temperature

2.Ripple and noise are tested at 20mhz of bandwidth via 12" twitsted pair-wire terminated with 0.1uf and 47uf parael cap.

3.Tolerance:set up tolerance,line regulation and load regulation are included

4.derating may be loaded with low input voltage, it should double check the detailed static characteristics

5.As power supply need to connected with final terminal equipment, which require the equipment to comply with EMC standard on the complete installation process again