Contact Platform Support
Help CenterASTM A678 GR.A/ASTM A678 GR.B/ASTM A678 GR.C/ASTM A678 GR.D Steel Plate
Related Products
-
S355JR/S355J0/S355J2/S355K2 STEEL PLATENegotiableMOQ: 40 Tons -
S355M/S355ML/S420M/S420ML/S460M/S460ML STEEL PLATENegotiableMOQ: 80 Tons
-
Abrasive Resistant Steel Plate 400NegotiableMOQ: 40 Tons
-
Corton Plate/Weathering Resistant Steel Plate/Weather Resistant Plate/S235J0W/S235J2W/S355J0W/S355J2W/S355K2WNegotiableMOQ: 100 Tons
-
ASTM A387 GR11 CL2 BOILER PLATENegotiableMOQ: 80 Tons
Specifications
ASTM A678 GR.A/ASTM A678 GR.B/ASTM A678 GR.C/ASTM A678 GR.D Steel plateASTM A678 GR.A/ASTM A678 GR.B/ASTM A678 GR.C/ASTM A678 GR.D Steel plate
Withdrawn Rationale:
This specification covers quenched-and-tempered carbon steel and high-strength low-alloy steel plates of structural quality for welded, riveted, or bolted construction.
Formerly under the jurisdiction of Committee A01 on Steel, Stainless Steel and Related Alloys, this specification was withdrawn in October 2010. This standard was withdrawn without replacement due to its limited use by the industry.
1. Scope
1.1 This specification covers quenched-and-tempered carbon steel and high-strength low-alloy steel plates of structural quality for welded, riveted, or bolted construction.
1.2 If the steel is to be welded, it is presupposed that a welding procedure suitable for the grade of steel and intended use or service will be used.
1.3 Plates under this specification are available in four grades as follows:
| Grade | Yield Strength, min, ksi [MPa] |
Tensile Strength, ksi [MPa] |
Maximum Thickness, in. [mm] |
| A | 50 [345] | 70–90 [485–620] | 11/2 [40] |
| B | 60 [415] | 80–100 [550–690] | 21/2 [65] |
| C | A | A | 2 [50] |
| D | 75 [515] | 90–110 [620–760] | 3 [75] |
A Varies with thickness. See Table 1.
1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system is to be used independently of the other.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
Send Inquiry to This Supplier
You May Also Like
-
0.35mm Electrical Pure Iron Cold Rolled Sheet for Solenoid Valve ManufacturingNegotiableMOQ: 1 Ton
-
High Strength Structural Plate Hot Rolled Alloy Steel Plate in StockNegotiableMOQ: 1 Square Meter
-
ASTM A36, Ss400, S235, S355, St37, St52, Q235B, Q345b Carbon Steel Sheet PlateNegotiableMOQ: 1 Ton
-
Electrical Pure Iron Cold Rolled Sheet for High-Efficiency Generator Rotor ProductionNegotiableMOQ: 1 Ton
-
Electrical Pure Iron Cold Rolled Sheet With 1.5T Saturation Flux Density for Industrial UseNegotiableMOQ: 1 Ton
-
Cold Rolled Electrical DT4C Cold Rolled Sheet/Plate Cold Rolled Stamping Shee for Electromagnetic ComponentsNegotiableMOQ: 1 Ton
-
High Magnetic Permeability Electrical Pure Iron Cold Rolled Thin SheetNegotiableMOQ: 1 Ton
-
DT4C Cold Rolled Thin Sheet 0.5-3.0mm Thickness for Electrical Motors and TransformersNegotiableMOQ: 1 Ton
-
Electrical Pure Iron Cold Rolled Thin Sheet Low Coercivity Soft Magnetic MaterialNegotiableMOQ: 1 Ton
-
Soft Magnetic Pure Iron Cold Rolled Sheet for Electrical Components ProductionNegotiableMOQ: 1 Ton
