20W PLN-20 MEANWELL/LED POWER SUPPLY/CE UL EMC

MODEL

PLN-20-12

PLN-20-18

PLN-20-24

PLN-20-36

PLN-20-48

OUTPUT

DC VOLTAGE

12V

15V

24V

36V

48V

CONSTANT CURRENT OPERATION VOLTAGE Note.5

9 ~ 12V

13.5 ~ 18V

18 ~ 24V

27 ~ 36V

36 ~ 48V

CURRENT RANGE

0 ~ 1.6A

0 ~ 1.1A

0 ~ 0.8A 

0 ~ 0.55A

0 ~ 0.42A

RATED CURRENT

1.6A

1.1A

0.8A

0.55A

0.42A

RATED POWER

19.2W

19.8W

19.2W

19.8W

20.2W

RIPPLE & NOISE (max.)  Note.2

2.5Vp-p

3.0Vp-p

3.0Vp-p

3.0Vp-p

3.8Vp-p

VOLTAGE ADJ. RANGE

VOLTAGE TOLERANCE   Note.3

10%

LINE REGULATION

3.0%

LOAD REGULATION

10%

SETUP, RISE TIME

2300ms / 230VAC 3000ms / 115VAC at full load

HOLD UP TIME (Typ.)

INPUT

VOLTAGE RANGE

90 ~ 277VAC 127~392VDC

FREQUENCY RANGE

47 ~ 63Hz

POWER FACT.or

PF  0.9 at 75~100% load, 115VAC/230VAC

EFFICIENCY (Typ.)

80%

81%

82%

83%

83.5%

AC CURRENT (Typ.)

0.4A/115VAC 0.2A/230VAC

INRUSH CURRENT (Typ.)

40A/230VAC

LEAKAGE CURRENT

0.5mA / 240VAC

PROTECTION

OVER CURRENT

95 ~ 110%

Protection type : Constant current limiting, recovers automatically after fault condition is removed

SH.orT CIRCUIT

Hiccup mode, recovers automatically after fault condition is removed.

OVER VOLTAGE

14 ~ 16V

19 ~ 22V

27 ~ 34V

41 ~ 46V

54 ~ 60V

Protection type : Shut off o/p voltage, clamping by zener diode

OVER TEMPERATURE

110   10  (TSW1)

Protection type : Shut down o/p voltage, recovers automatically after temperature goes down

ENVIRONMENT

W.orKING TEMP.

-30 ~ +60^oC (Refer to output load derating curve)

W.orKING HUMIDITY

20 ~ 90% RH non-condensing

ST.orAGE TEMP., HUMIDITY

-40 ~ +80^oC , 10 ~ 95% RH

TEMP. COEFFICIENT

0.06%/^oC (0 ~ 50^oC )

VIBRATION

10 ~ 500Hz, 2G 10min./1cycle, period f.or  60min. each along X, Y, Z axes

SAFETY &EMC(Note 4)

SAFETY STANDARDS

IEC61347-1, IEC61347-2-13, TUV EN61347-1, EN61347-2-13, UL8750, IP64 approved

WITHSTAND VOLTAGE 

I/P-O/P:3.75KVAC

ISOLATION RESISTANCE

I/P-O/P:100M Ohms/500VDC / 25 / 70%RH

EMI CONDUCTION & RADIATION

Compliance to EN55015

HARMONIC CURRENT

Compliance to EN61000-3-2 Class C( 75% load);EN61000-3-3

EMS

IMMUNITY

Compliance to EN61000-4-2,3,4,5,6,8,11;EN61547, light industry level,  criteria A

OTHERS

MTBF

643.6Khrs min. MIL-HDBK-217F (25 )

DIMENSION

148.5*38.5*28mm (L*W*H)

PACKING 

0.18Kg; 60pcs/12.8Kg/0.9CUFT

NOTE

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25^oCof ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacit.or.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. Derating may be needed under low input voltage, please check the static characteristic f.or m.ore details.

5. Constant current operation region is within 75% ~100% rated output voltage. This is the suitable operation region f.or LED related applications, but please reconfirm special electrical requirements f.or some specific system design.

6. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC perf.ormance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.