Explosive-proof Leak detector for Franklin Fillng System, Fuel Filling Pipe Leakage detection,water oil leak alarm

GH-SL Pipeline leakage detector is composed of a SYW-SL leakage detection sensor, GH-SL detecting controller and other related accessories,.The leakage detector have real-time monitoring function. It is specially designed for detecting water and oil between the pipeline interlayer .When leakage occurs between the pipeline interlayer , the leaked liquid will gravity to the bulk tank , the SYW-SL sensor who keep in the bulk tank can detect the leaked liquid and make the signal to GH-SL controller , the controller get the signal and make the lights and audio alarm .Users can make a timely response and take related measures to avoid potential safety hazards  and environmental pollution based on the alarm. 

Detector voltage:220VAC                  Sensor voltage :+12VDC

Alarming mode :audible and visual alarm   Inspection time:≤1s

Range of temperature :-40℃~+70℃      Environment humidity:<85%

Output mode:switch value                 Cabling mode:Parallel input

Detector size:300*180*113                 Number of supported sensors :6

Product Features:

1,Running safety, stability, easy maintenance: sensor device is composed of liquid         float switch, with simple structure and stable running.

2,High sensitivity: response time is less than one second.

3,Less cost, high efficiency:one leakage detector can take six leakage

detection sensor, each leakage detection sensor can take four double-layer pipeline  and one manhole well.

4,Simple installation and wide application : it can be easily installed in a    gas station, oil depot and other regions.

5,Relay output port, can make the equipment chain control with a third party.

6,485 communication port can realize uploading function.

Install Leakage Detection Sensor:

1,Put the Leakage detection sensor vertical installed in  the fixed bolt of manhole well.

2,Connection pipe test ports and detection device ports with oil conduit,oil conduit need short enough to avoid bending.

3,Connect snorkel to his connection Port.Complete the snorkel connection,the specific location is : on the manhole well inner wall of oil tank , directly above 1m and vertical direction.

4,Installation,use and maintenance of detection sensor should also comply with the product manual,GB3836-2010 explosion-proof criteria,Design of automotive filling oil and gas,construction specifications and other national standards. It is only allowed to make the installation construction who have the qualification of explosion-proof electrical equipment installation.

Installing GH-SL Leakage Detector: 

1,Leakage detector and leakage detection device connection cables is recommended to use shielded cable 2 * 1.

2,With fixed screws to fix the leakage detector on the wall .

3,Put out the signal cable which contact the sensor in the manhole well and get through the threading pipe to the control room, connect the two signal lines to terminals of detector circuit board (regardless of the positive and negative ), attention :the label of terminals should correspond to the label of manhole well detecting sensor.

4,Adjust leakage detector DIP switch :  according Annex 1 to keep the DIP switch shows numerical concur with the enabled leakage sensor quantity.

5,Open the leakage detector power switch , if no leakage happens , all indicator light shows green; when leakage happens, the corresponding light shows   red; at the same time alarm rang ,relay start working.

6,When Alarm rang, users can turn off the "silence switch",on the left side of the detector to eliminate voice.

7,In the process of normal use ,Press "Detection button" ,leakage detector can simulate the penetration function in turn, to test indicator is normal or not .After the simulation test then return to normal state.

1. Provide necessary conditions for the customers visiting factory.

2. Good quality with competitive price.

3. All products have been strictly Quality Checked before shipping.

4. Free repair within 12 months.

5. Great after-sale service and offer solution within 24 hours.

6.OEM is ok.

1:How long will you give me the reply?

we will contact you in 2 hours as soon as we can.
2:Could I get samples?
Yes,we have materials in stock to help you to get the samples as soon as we can.
3:How about the quality of the magnets?
We have the certification of ISO, we could send the certification test of our company to you.
4:How is the price?
As we believe the quality is the most important,we will provide the best quality and lowest factory price.
5:Could you provide me the shortest lead time?
We have materials in our stock,if you really need,you can tell us and we will try our best to satisfy you.
6:Could I visit your factory?
Of course,if you need we will help you to visit our factory.
7:If I have paid,when will you help me to produce?
When we have received the money in our account,we will give you the receipt and arrange to produce immediately.

Qingdao Guihe Measurement & Control Technology Co., Ltd was founded in 2002, is a professional manufacturer of petroleum equipment. We specialized in producing Magnetostrictive liquid level meter (tank gauging system), Underground fuel tank volume table calibration system, Double layer tank leakage detector, Double layer pipeline leakage detector, Tank car liquid level meter, Human body electrostatic discharge alarm. We also providing different customers with personalized solutions.