Contact Platform Support
Help CenterAPP Modified Bituminous Waterproof Membrane
Related Products
-
SBS Modified Bitumen Waterproof MembraneUS$ 2 - 5.5MOQ: 10 Square Meters -
APP Modified Bitumen Waterproof MembraneUS$ 2 - 5.5MOQ: 10 Square Meters
-
SBS/APP Modified Bituminous Waterproof MembraneUS$ 2 - 5.5MOQ: 10 Square Meters
-
SBS Modified Bituminous Waterproof FeltUS$ 2 - 5.5MOQ: 10 Square Meters
-
APP Modified Bituminous Waterproof FeltUS$ 2 - 5.5MOQ: 10 Square Meters
JH-200 APP Modified Bituminous Waterproof Membrane is made of high-quality bitumen which is modified by APP, APAO or APO, enhanced reinforcement and different surface materials.
High temperature resistance, high elongation ability, strong tensile strength, good abrasive resistance and easy to pave.
1. Industrial and civil roofing construction such as insulation roofs, planted roofs, roof parking lots and inverted roofs, etc.
2. Industrial and civil underground construction, indoor swimming pools, fire reservoirs, etc.
3. Tunnels, subways, concrete bridges, sewage plants and refuse landfills, etc.
4. Water conservancy facilities such as pools and water channels, etc.
Performance Standard GB 18242-2008
| Item | Index | |||||
| Ι | ΙΙ | |||||
| PY | G | PY | G | PYG | ||
| Content of Soluble Substance (G/m2) | 3mm | 2100 | ||||
| 4mm | 2900 | |||||
| 5mm | 3500 | |||||
| Heat Resistant | ºC | 110 | 130 | |||
| ≤mm | 2 | |||||
| Low Temperature Flexibility/ºC | -7 | -15 | ||||
| No Crack | ||||||
| Water Impermeability (30min) | 0.3MPa | 0.2MPa | 0.3MPa | |||
| Tension |
Maximum Tension (N/50mm) ≥ |
500 | 350 | 800 | 500 | 900 |
| Secondly Maximum Tension (N/50mm) ≥ | 800 | |||||
| Elongation Rate | Maximum Elongation Rate / % ≥ | 30 | 40 | |||
| Maximum Elongation Rate / % ≥ | 15 | |||||
| Increased Quality After Immersion % ≤ | RE/S | 1.0 | ||||
| M | 2.0 | |||||
1, Torch-applied method and cold adhesion method are both feasible , or we can use these two methods together during the construction, which means cold adhesion method used at the main part and torch-applied method used at the seam.
2, Torch-applied method: use spray guns or blowtorches to heat the membrane and the base surface. While the bitumen on membranes is melting, roll the membrane forward, then use roller to make the membranes and the base surface stick together.
3, Cold adhesion method: brush adhesives on the base surface and membranes, after a while, pave the membranes, meanwhile press out the air with the roller until the membranes and the base surface stick together tightly and flat-wise.
Send Inquiry to This Supplier
You May Also Like
-
CE and ASTM Self Bituminous Adhesive Waterproof Membrane for Roof, Window, Door, Road, Bridge, Ship Deck Anti Corrosion Protection Pipe TapeNegotiableMOQ: 100 Rolls
-
1.5mm Thick UV-resistant Geomembrane High Strength Waterproof Membrane for Dam and Canal Lining BOLIUS$ 0.15 - 0.20MOQ: 10 Square Meters
-
Non-curable Rubber Paint Rubber Asphalt Waterproof Coating Made in ChinaUS$ 1.5 - 6MOQ: 500 Kilograms
-
Low Cost Waterproof Material ManufactureUS$ 1,000 - 50,000MOQ: 1 Set
-
PTFE Architectural Membrane MaterialNegotiableMOQ: 1
-
Special Compound BaseUS$ 0.12 - 0.25MOQ: 7000 Square Meters
-
PolyLock/HDPE Lock/ E Lock/ HDPE E Lock/Geomembrane Attaches HDPE GeomembranesUS$ 10 - 50MOQ: 1 Piece
-
Breathable House Wrap Membrane Roofing Waterproofing MembraneUS$ 0.42 - 0.42MOQ: 5000 Square Meters
-
<MIicroVENT> Waterproof Vent MembraneUS$ 0.1 - 3MOQ: 10000 Pieces
-
Self Adhesive Polymer Modified Bitumen Waterproof MembraneNegotiableMOQ: 2000 Square Meters
