Home > Products > 3 Phase stepper motors and controllers > 3 Phase Stepper Controller
3 Phase Stepper Controller
- Durban Lanseria
You May Like
Product Details
Condition | New | Type | Other | |
Place of Origin | South Africa | Brand Name | Astroware | |
Model Number | 3DM583 | Voltage | 50VDC | |
Power(W) | 5.9 | Dimension(L*W*H) | 34 | |
Weight | 1.7 | Certification | CE,ISO,SGS | |
Warranty | 1 Year | After-sales Service Provided | No overseas service provided |
Product Description
The 3DM583 is a versatility fully digital stepping driver based on a DSP with advanced control algorithm. It brings a unique level of system smoothness, providing optimum torque and nulls mid-range instability. Motor self-test and parameter auto-setup technology offers optimum responses with different motors and easy-to-use. The driven motors can run with much smaller noise, lower heating, smoother movement than most of the drives on the markets. Its unique features make the 3DM683 an ideal solution for applications that require low-speed smoothness.
- High performance, low noise and lost cost
- Low driver heating and low motor heating
- Supply voltage up to 50 VDC
- Output current up to 8.3A (RMS 5.9A)
- Input signal TTL compatible
- Automatic idle-current reduction
- Suitable for 3-phase stepping motors, including 3 lead and 6 lead motors
- Optically isolated differential input signals, pulse frequency up to 300 KHz
- 8 selectable resolutions up to 10000 steps/rev
- DIP switch current setting with 16 different values
- PUL/DIR & CW/CCW modes optional
- Over-voltage, short-voltage, over-current and short-circuit protection
- Small size for easy mounting
The 3ND583 is a high resolution 3-phase microstepping driver based on precision current control technology. It’s suitable for driving 3-phase hybrid stepping motors from NEMA size 17 to 34. By using the advanced pure-sinusoidal current control technology, both the noise and vibration of the stepping motor have been greatly reduced, which makes the stepping motors offer servo-like performances. Compared to the 3MD560, it’s lighter and smaller, and compared to most of the microstepping drivers in the market, both driver heating and motor heating have been reduced by 15-30%.
Selecting Microstep Resolution and Drive Output Current
The 3ND583 uses an 8-bit DIP switch to set motor dynamic current, standstill current and microstep resolution, as shown below:
Microstep Resolution Selection
Microstep resolution is set by SW6, 7, 8 of the DIP switch as shown in the following table:
Steps/rev.(for 1.2o motor) | SW6 | SW7 | SW8 |
200 | on | on | on |
400 | off | on | on |
500 | on | off | on |
1000 | off | off | on |
2000 | on | on | off |
4000 | off | on | off |
5000 | on | off | off |
10000 | off | off | off |
Current Settings
The first four bits (SW1, 2, 3, 4) of the DIP switch are used to set the dynamic current. Select a setting closest to your motor’s required current.
Peak Current | RMS Current | SW1 | SW2 | SW3 | SW4 |
2.1A | 1.5A | off | off | off | off |
2.5A | 1.8A | on | off | off | off |
2.9A | 2.1A | off | on | off | off |
3.2A | 2.3A | on | on | off | off |
3.6A | 2.6A | off | off | on | off |
4.0A | 2.9A | on | off | on | off |
4.5A | 3.2A | off | on | on | off |
4.9A | 3.5A | on | on | on | off |
5.3A | 3.8A | off | off | off | on |
5.7A | 4.1A | on | off | off | on |
6.2A | 4.4A | off | on | off | on |
6.4A | 4.6A | on | on | off | on |
6.9A | 4.9A | off | off | on | on |
7.3A | 5.2A | on | off | on | on |
7.7A | 5.5A | off | on | on | on |
8.3A | 5.9A | on | on | on | on |
Note: Due to motor inductance, the actual current in the coil may be smaller than the dynamic current setting, particularly under high speed condition.
Connector P1 Configurations
Pin Function | Details |
PUL+(+5V) | Pulse signal: In single pulse (pulse/direction) mode, this input represents pulse signal, effective for each rising edge or falling edge (set by inside jumper J1); 4-5V when PUL-HIGH, 0-0.5V when PUL-LOW. In double pulse mode (pulse/pulse) this input represents clockwise (CW) pulse. For reliable response, pulse width should be longer than 1.5μs. Series connect resistors for current-limiting when +12V or +24V used. |
PUL-(PUL) | |
DIR+(+5V) | DIR signal: In single-pulse mode, this signal has low/high voltage levels, representing two directions of motor rotation; in double-pulse mode (set by inside J1), this signal is counter-clock (CCW) pulse, effective for low level. For reliable motion response, DIR signal should be ahead of PUL signal by 5μs at least. 4-5V when DIR-HIGH, 0-0.5V when DIR-LOW. |
DIR-(DIR) | |
ENA+(+5V) | Enable signal: This signal is used for enabling/disabling the driver. High level (NPN control signal, PNP and Differential control signals are on the contrary, namely Low level for enabling.) for enabling the driver and low level for disabling the driver.. Usually left UNCONNECTED (ENABLED). |
ENA-(ENA) |
Connector P2 Configurations
Pin Function | Details |
GND | DC power ground. |
VDC | DC power supply, (20~50)VDC, Including voltage fluctuation and EMF voltage. |
U | Motor Phase U |
V | Motor Phase V |
W | Motor Phase W |
Contact Us
- Walbac Tool And Die
- Contact nameGerhard Koekemoer Chat Now
- Phone0027-11-836269380
Product Categories
3 Phase stepper motors and controllers | Double Head laser | Drag Chains | HTD-3M Timing Belts and Pulleys |
Laser Machine Parts | New Products | Single Head Laser | Stamp Pads |
Stamps |
New Products
-
Mounting Brackets L-wide 23 Frame
-
Mounting Brackets L-narrow 34 Frame
-
Mounting Brackets L-wide 34 Frame
-
Laser Cutting Engraving Machine DF1280/80W
-
Laser Cutting Engraving Machine DF1610/80W
-
Laser Cutting Engraving Machine
-
Drag Chain 10x10mm/meter
-
Drag Chain 15x20mm/meter 28mm Radius
-
Drag Chain 25x77mm/meter 75mm Radius
-
15 Teeth HTD-3M Timing Pulley
-
20 Teeth HTD-3M Timing Pulley
-
38 Teeth HTD-3M Timing Pulley
Popular Searches
- extruder component
- screw barrel
- screw element
- rapid prototype
- prototyping
- 3d model
- titanium alloy
- metal prototype
- api coupling
- grease fitting
- iron machining
- stop service
- 3d printing service
- assembly service
- oil nozzle
- bakelite knob
- tool accessory
- grease nipple
- plastic auto part
- rapid prototyping
- final inspection service
- mechanical transmission part
- precision plastic machining
- drill bushing
- fastener part
- rubber piston
- other motorcycle part
- auto component
- other motorcycle accessory
- plastic prototype
Recommended Products
- KD400LYServo-integrated Medium-speed Wire-cut EDM Machine
- Cutter Wire Cutting in the Middle of the Kade
- Reliable Waterjet Cutting Machine for Stone Marble Porcleain Cutting Industry
- 20 Dual Spindle Precision 5 Axis Swiss Type CNC Lathe Machine for Metal-Cutting
- 325 36mm Spindle Bore Swiss Type CNC Lathe Machine for Sale
- Yuanjie CNC Swiss CNC Lathes With Tracer Magazine Barfeeders
- NEW 32 CNC Swiss-type Automatic Lathe
- Small Metal Lathe1120 Swiss-Type CNC Lathe With 3 Axes
- Small Precision Brand Swiss Type CNC Lathe
- 363 High Accuracy Small CNC Lathe Electric Spindle Swiss Type CNC Lath
- Swiss Type CNC Lathe Small Parts High Precision CNC Lathe Machine 164
- 12mm 5 Axis 7 Axis Swiss Type CNC Lathe Longitudinal CNC Lathe Sliding Head CNC Lathe Small CNC Machine
Find Similar Products By Category
- Manufacturing & Processing Machinery > Machine Tools > CNC Machine Tools
- Please Enter your Email Address
- Please enter the content for your inquiry.
We will find the most reliable suppliers for you according to your description.
Send Now-
Gerhard Koekemoer
Hi there! Welcome to my shop. Let me know if you have any questions.
Your message has exceeded the limit.

- Contact supplier for lowest price
- Customized Request
- Request Sample
- Request Free Catalogs
Your message has exceeded the limit.
-
Purchase Quantity
-
*Sourcing Details
Your inquiry content must be between 10 to 5000 characters.
-
*Email
Please enter Your valid email address.
-
Mobile