Compressed garbage truck, bucket hanging garbage truck, swing arm garbage truck, bucket lifting garbage truck

Upper deck configuration: The upper deck container has a carrying capacity of 6.5 cubic meters (about 4 tons of garbage, the weight may vary depending on the type of garbage). The container is made of high-quality manganese steel of Wuhan Iron and Steel Corporation, with an edge thickness of 4mm and a bottom thickness of 4mm. It is used to load household waste and consists of a sealed garbage can, filling, dozer blade, hydraulic transmission system and electrical control system. The vehicle is fully enclosed and adopts integrated electrical and hydraulic technology. With the help of a combined mechanical, electrical and hydraulic automatic control system, waste is dumped, crushed, flattened and forcibly loaded using special equipment such as bins, fillers and shovels, squeezed into the wagons, compacted and unloaded. In the compression process, all the sewage enters the sewage pool, which solves the problem of secondary pollution in the process of garbage transportation. Users can choose to install different turning mechanisms according to different garbage collection methods: flip standard trash cans (300L), plastic trash cans (120/240L), plastic trash cans (660L), or pneumatic sealing lids, triangular buckets, large floor trash cans, swing arm trash cans and other flipping mechanisms.

Vehicle performance characteristics:

1. Electro-hydraulic linkage control: the control system of the car comprehensively exerts the advantages of electronic control and hydraulic control. The hydraulic valve group is controlled by an electronic control system, which improves the reliability and efficiency of use.

2. Automatic control of engine power output: Engine power output control, also known as throttle control, can be fully automated through the electrical system to meet the power requirements of garbage filling cycle and pushing. Under other working conditions, the engine will automatically idle to reduce power loss and failure rate, reduce fuel consumption and improve use economy.

3. Frame structure: The trash can is made of steel beams and welded steel plates to form a solid frame structure. The side and top surfaces are curved, beautiful in appearance, light in weight, good in stress, and not deformed; The dozer blade is composed of a rectangular tube skeleton and a folding plate, which is not only light in structure, but also can evenly distribute garbage and discharge materials thoroughly and cleanly; The packing is mainly composed of packing shells, slide plates, scrapers and other components. Each component adopts a well-stressed beam plate or box structure, which is strong and lightweight.

4. Sealed treatment to eliminate secondary pollution: garbage is in a closed state during compression, loading and transportation. The seam surface between the garbage can and the filler is equipped with a special rubber sealing strip, which is compressed and sealed with a locking device; The sewage tank is equipped with a unique drain valve, which seals reliably and is not easy to clog. The optional fuel filler cover completely covers the fuel filler, eliminating the phenomenon of garbage and dust flying caused by vehicle exhaust air disturbance during transportation, making the appearance more beautiful.

5. Hydraulic lifting safety circuit: two-way balance valve is installed in the hydraulic system of the lifting loader. The valve not only guarantees a smooth descent of the filler, but also isolates the direct connection between the lift cylinder and the hydraulic hose. Even if the oil pipe bursts, the oil filler will not fall suddenly, which improves the safety of use.

6. Advanced electronic control system: controlled by the CAN bus board controller, the control circuit is generated inside the controller, and the logic circuit is used to ensure that each operation instruction is executed in order. At the same time, it ensures that each operation instruction is interlocked, and only external lines are used to connect it, so as to reduce the failure rate, avoid accidents caused by misoperation, and improve reliability; The special emergency brake button can stop the garbage filling mechanism in any state or position, ensuring the safety of operators and equipment.

7. The combination of packing and box adopts a locking mechanism, and the slide plate is guided by a nylon slider. The seam between the packing and the box is reasonably structured, and the locking and sealing technology is adopted. The skateboard track is made of high-strength manganese steel material and stamped as a whole. The skateboard movement is guided by a nylon slider.

8. Automatic and manual operating systems: Each mechanism operates in automatic and manual modes.

9. Convenient operation and control: the operation control box is installed in the cab and the rear of the vehicle. The in-cab operator control box controls the loading and unloading of the material and selects the mode of operation (e.g. automatic or manual). The operation control box at the rear of the vehicle controls the operation of the filling mechanism and the turning mechanism, which is very convenient to use. Especially in landfills, workers can complete unloading and sewage discharge without getting out of the car.

10. High-quality components: The key components of the electrical and hydraulic systems are all well-known components, such as controllers, multi-channel reversing valve groups, buttons, cylinder seals, etc., which improve the reliability of garbage trucks.