PFEA113-IP65 3BSE050092R65 Tension gauges

PFEA113-65 3BSE050092R65 Tension gauges

The abb force measuring indenter is manufactured according to ABB's patented magnetoelastic technology, also known as the piezomagnetic principle. The control unit supplies the indenter with the excitation power, processes the output signals from the indenter and transmits the measured values to an external system. The PFEA111/PFEA112 control unit can be set up and commissioned by the touch of a button. These functions are very easy to implement thanks to the user-friendly interface. Measured values are displayed in the PFEA111/PFEA112 and are communicated to external displays or other peripheral devices via the analogue outputs. Status or alarm messages are displayed on the PFEA111/PFEA112 control unit or output via ProfisBus DP (only available for PFEA112).

ABB TENSOMETER Millmate strip tension measurement - principle of pressure head measurement

The piezomagnetic sensor works on the principle that the permeability of a magnetic material changes under the influence of a mechanical force. The sensor is made from a single piece of stainless steel with four holes punched in the stainless steel body. Through these four holes two sets of coils are wound at an angle to each other. When an alternating current is applied to the primary coil, a magnetic field is generated in the primary coil. Since the primary and secondary coils are at an angle to each other, no magnetic field is generated in the secondary coil as long as there is no load on the sensor. When a mechanical force is applied in the measuring direction of the sensor, the direction of propagation of the magnetic field in the primary coil changes and the secondary coil is incorporated into the magnetic field. As a result of the change in the magnetic field in the secondary coil, an induced potential is generated in this coil. The control unit converts this induced potential into a DC voltage signal proportional to the corresponding force being measured.

Features of ABB's Millmate strip tension measuring - piezomagnetic indenter

The indenter is made from a single piece of machined stainless steel. It is sensitive only to the force in the direction of measurement. Forces in other directions are absorbed by the indenter due to its special structural design and thus have no effect on the forces in the measuring direction.

Wide measuring range: measuring range of 40:1 up to 200% of the rated range, minimum 5% of the rated range.

Repeatable large overload capacity: 10 times the electrical overload capacity of the rated range and more than 30 times the mechanical overload capacity of the rated range, without plastic deformation or fatigue

No calibration required

No physical drift

High power sensor output signal (100mV):Large output signal and carrier frequency for excellent immunity to interference

Low impedance output (10 ohms): the indenter has better noise immunity and the output signal is insensitive to insulation conditions, making it more suitable for the harsh operating environment of mills. The pressure head is protected to IP65 for normal operation in sites with splashing.

Xiamen Xiongba Electronic Commerce Co. LTD

FROM：Mr. Wei

E-Mail：2322181769@qq.com

TEL/WeChat:15396237607

PFEA101 for closed loop control of constant tension during unwind and winding, with the possibility of connecting pressure measuring elements and torque output devices such as brakes, clutches and motors. 

PFEA111 Tension controller with two pressure measuring elements, compact and rail mounted. 

The PFEA112 adds Profibus-DP fieldbus communication to the PFEA 111. 

PFEA113 Tension controller with four load cells, Profibus-DP fieldbus communication and six configurable analogue outputs. 

PFRL 101A radial force measuring element, rated load 0.5KN. 

PFRL 101B Radial pressure measuring element, rated at 1.0KN. 

PFRL 101C Radial pressure measuring element, rated from 0.5 to 2.0KN. 

PFRL101D Radial pressure measuring element, rated load 5.0KN. 

PFTL301E Mini paper web tension horizontal measuring element, measuring range: 0.1~1KN 

PFCL301E Mini web tension vertical measuring element, measuring range: 0.2~1KN 

Power Systems Division: The Power Systems Division offers a complete range of systems and services for transmission and distribution networks and power plants worldwide, with a focus on substations and substation automation systems. In addition, the division offers Flexible AC Transmission Systems (FACTS) and High Voltage Direct Current (HVDC) transmission systems as well as grid management systems. In the Power Generation business area, the Power Systems Division offers instrumentation products as well as control and auxiliary devices for power plants.

Discrete Automation and Motion Control: The Discrete Automation and Motion Control segment supplies products, solutions and services that help customers improve productivity and energy efficiency. Its motors, generators, drive systems, programmable logic controllers, power electronics and robotics products are used in a wide range of automation applications in the areas of power, motion and control. The business segment's leadership in the wind turbine industry and its growing product line in the solar sector will further contribute to the development of the existing skills, channels and operating platforms of the Discrete Automation & Motion Control division in the industrial sector.

Power electronics: SYNCHROTACT Concurrent equipment, control systems.

If you need to inquire or purchase ,please send the product models to my email or call me directly .

Contact detail:Mobile/ WeChat/ WhatsApp:+86-15396237607

E-mail:2322181769@qq.com

QQ: 2322181769