ACU-01B 3HNA024871-001/03

Brand:ABB

Type:ACU-01B 3HNA024871-001/03

Origin: the Swiss

Warranty: 365 days

Colour: new/used

Shipping method: Courier delivery

Module of PLC, DCS, ESD system card, the card is a vibration monitoring system, steam turbine control system module, the advantages of the gas generator spare parts brand: Allen Bradley, BentlyNevada, ABB, Emerson Ovation, Honeywell DCS, Rockwell ICS Triplex, FOXBORO, Schneider PLC, GE Fanuc, Motorola, HIMA, TRICONEX, Prosoft etc. Various kinds of imported industrial parts of our products are widely used in metallurgy, petroleum, glass, aluminum manufacturing, petrochemical industry, coal mine, papermaking, printing, textile printing and dyeing, mechanical, electronic manufacturing, automobile manufacturing, plastic machinery, electric power, water conservancy, water treatment/environmental protection, boiler heating, energy, power transmission and distribution and so on.

parameter is capacitance (energy storage), so an 85° C, general-purpose type (such as are listed below) is acceptable. Panasonic G-AA series 1.375 x 4.125 8,200 µf 100 V EEGAA2A822CKE 2 x 4.125 22,000 µf 100 V EEGAA2A223FKE 3 x 4.125 47,000 µf 100 V EEGAA2A473HKE Cornell Dubilier DCMC series 1.375 x 4.125 8,600 µf 100 V DCMC862U100AC2B 2 x 4.125 20,000 µf 100 V DCMC203U100BC2B 3 x 4.125 49,000 µf 100 V DCMC493U100DC2B United Chemicon U36D series 1.375 x 4.625 8,200 µf 100 V U36D100LG822M35X117HP 2 x 4.625 18,000 µf 100 V U36D100LG183M51X117HP 3 x 4.625 47,000 µf 100 V U36D100LG473M76X117HP A.2 TWO POWER SUPPLY OPERATION Powering the drive control power separately from the bus power has the advantage that fault and status information is preserved when bus power is down for safety. Wire the control supply positive terminal to J1-1 (+CTRL) and the control supply negative terminal to J1-2 (Bus/Ctrl Gnd). Wire the main supply positive terminal to J1-3 and its negative terminal to J1-2. J1-2 is a shared ground for control power and main power. Separate ground wires from the two supplies should join at or near the shared drive ground pin (J1-2). 

NOTE The drive can be damaged if the supply voltage exceeds 90 V, even briefly. A.2.1 Control Supply (J1-1 to J1-2) The voltage range of the control supply is + 10 to + 90 V. This supply can be either unregulated or regulated. However, it must be isolated from the power line as its negative terminal is typically earthed for safety and commoned with main power negative terminal. For reliable starting, the control supply should have a peak power rating of at least 20 W. A typical continuous control power drawn by an S200 DC drive is 2 to 8 W. A single, relatively low power, low voltage supply (+ 12 V or + 24 V) can provide control power and I/O power for multiple drives. A.3 MULTI-AXIS CONSIDERATIONS In multi-axis applications, the drive’s power terminals can either be wired separately to the power supplies or paralleled locally (daisy-chained) and then wired to the power supplies. In the latter case, increase the wire size to handle the higher current. NOTE Locally paralleling the main power terminals of multiple drives parallels the internal bus capacitors of the drives (200 µf per drive). This allows the PWM currents of the drives to spread out, thereby lowering the temperature of the capacitor in the hottest drive.