Home > Products > steel rolling > LDC-X200 Laser Diameter Measuring System
LDC-X200 Laser Diameter Measuring System
- 5000 Piece / Pieces per Month
- T/T Credit Card PayPal
- Sand Water Filter/Water treatment plants
- Automatic Doypack Seal Machine (insert and sealing machine)
- IPX3/IPX4 Hand-held Water Spray Nozzle Test Device IEC 60529
- IPX5,IPX6 Jet Nozzle of IEC 60529, Brass material
- Adjustable and multifunctional Spring Impact Hammer IK01-IK07 Level Tester
- Test probe 43 IEC 61032-Probe 43-Figure 17 Jusdtest
Product Details
Brand Name: | ZFY | Place of Origin: | China | Model Number: | LDC-X200 |
Product Description
LDC-X200 Laser Diameter Measurement System
Overview
The non-contact diameter measuring system, is mainly used in the measurement of the outer diameter of various wire rods, bars, wires and pipes. The system can detect the change of the diameter (outer diameter) of the measured object in real time under the high temperature state.
The working principle
The diameter measuring system takes the laser scanning method as an example. It adopts the probe imported from Japan, which can achieve an accuracy of plus or minus 2 microns in the range of 0.3 to 30 mm. The acquisition frequency reaches 2000 times/second. The probe uses a self-excited infrared light source, which overcomes the measurement problem in dim environments.
It adopts the measurement method of pulse parallel light scanning, and has a strong ability to resist the jitter of the measured object. (As shown in Figure 1) Since the shaking frequency of the measured object is much smaller than the scanning frequency, when the measured object A moves in the shakeable area, the measurement result will be able to ensure its accuracy because the time it blocks the beam does not change.
Figure 1: Probe Scanning Radiation Area
The detection principle is as follows
Figure 2: Working Principle
First, the crystal oscillator generates self-excited high-frequency pulses, which are sent to the comparator and the stepping servo motor respectively. The stepping servo motor drives the octahedral prism to rotate at a high speed, and reflects the infrared laser emitted by the laser generator to the convex lens A. It becomes parallel light, and then collects on the photosensitive element C through the convex lens B in the infrared receiving probe. The photosensitive element C converts this signal into a corresponding electrical signal and sends it to the other end of the comparator to compare with the original signal.
When there is no object to be measured in the measuring probe, the pulse signal at both ends of the comparator will be the same. Therefore, there is no difference output: when there is an object to be measured in the measuring probe, the photosensitive element C will output no pulse signal during the period of scanning through the object to be measured. Therefore, there will be a difference input for a period of time at both ends of the comparator, which corresponds to the diameter of the measured object. By calculating the oscillation period of the pulse and the length of the time slice without pulse, the diameter of the measured object can be known.
The composition and functions of the system
The system consists of the following main parts (as shown in Figure 1)
1. A measurement frame with four pairs of high-frequency laser scanning probes and non-contact infrared thermometers is installed
2. Four intelligent signal processors connected with four pairs of high frequency laser scanning probes
3. Cold air blowing system for cooling and cleaning the measuring frame
4. High-performance intelligent controller responsible for front-end data signal processing and network communication
5. Data processing and analysis system installed with industrial grade PC, monitor and printer
The technical indexes
Wuhan CenterRise M&C Engineering CO., Ltd.
more info, please contact zero zero eight six one three nine nine five five eight eight five nine seven
Contact Us
- Wuhan CenterRise M&C Engineering CO., Ltd.
continuous casting | steel rolling |
- IEC61032-Probe 41-Figure 16 Test probe 41
- IEC61032-Probe 32-Figure 15 Test probe 32
- Test probe 31 IEC61032-Probe 31-Figure 14
- Jointed Child Finger Probes IEC 61032-Probe 19-Figure 13 R 2.5±0.05 mm
- Test probe 18 of IEC 61032 R4.3mm Jointed Child Finger Probes
- Digital recorder for Lugeon testing
- MRU Subsea maring motion reference unit
- MRU maring motion reference unit
- eMRU motion reference unit
- IEC61032-Probe 14-Figure 10 Test probe 14
- Short Test Pin Probe IEC61032-Test Probe 13-Figure 9
- Long Test Pin Probe IEC61032-Probe 12-Figure 8 JSD-08
- IEC61032-Test Probe 11-Figure 7 Φ12mm IEC 60601
- IEC 61032:1997-test Probe 2-Figure 6 with handle
- IEC61032-Probe D-Figure 4 Test probe D 1mm diameter
- Test probe C IEC61032-Probe C-Figure 3 MODEL JSD-03
- IEC61032-Probe B-Figure 2 Test probe B IP2X test
- Test probe A IEC 61032-Probe A-Figure 1 JUSDATEST
- Test finger ISO 20957-1:2013 Figure 1
- JSD-K02 Test probe ABCD-Power supply Kit of IEC 61032:1997
- PRS10 Rubidium Oscillator
- HY-408 magnetic compass for naval
- The BX992 is a dual-antenna receiver enclosure with integrated inertial navigation system powered by the BD992-INS
- Trimble BD992 Dual-antenna single board solution for precise position and heading
Popular Searches
Find Similar Products By Category
- Measurement & Analysis Instruments > Other Measuring & Analysing Instruments
- Buy on GoldSupplier.com
- How to Buy
- Browse by Catagories
- Browse by Hot Regoins
- Private Sourcing Events
- Sell on GoldSupplier.com
- How to Sell
- Post Products
- Manage Products
- Manage Groups
- About
- About Us
- Link to Us
- Contact Us
- Sitemap
- Please Enter your Email Address
- Please enter the content for your inquiry.
We will find the most reliable suppliers for you according to your description.
Send Now-
sales
Welcome to my shop! Glad to serve you!Please send your question!
Your message has exceeded the limit.
Your message has exceeded the limit.
-
-
Your inquiry content must be between 20 to 5000 characters.Send Now.
-
Please input the mailbox.
-