Small Capacity Type SGMCS-10C3C11 Yaskawa Direct Drive Servo Motor

CAUTION

• Conduct trial operation on the servomotor alone with the motor shaft disconnected from machine to avoid any unexpected accidents. Failure to observe this caution may result in injury.

• Before starting operation with a machine connected, change the settings to match the parameters of the machine. Starting operation without matching the proper settings may cause the machine to run out of control or malfunction.

• Forward run prohibited (P-OT) and reverse run prohibited (N-OT) signals are not effective during zero point search mode using parameter Fn003.

• When using the servomotor for a vertical axis, install the safety devices to prevent workpieces to fall off due to occurrence of alarm or overtravel. Set the servomotor so that it will stop in the zero clamp state at occurrence of overtravel. Failure to observe this caution may cause workpieces to fall off due to overtravel.

• When not using the normal autotuning, set to the correct moment of inertia ratio. Setting to an incorrect moment of inertia ratio may cause vibration.

• Do not touch the SERVOPACK heatsinks, regenerative resistor, or servomotor while power is ON or soon after the power is turned OFF. Failure to observe this caution may result in burns due to high temperatures.

• Do not make any extreme adjustments or setting changes of parameters. Failure to observe this caution may result in injury due to unstable operation.

• When an alarm occurs, remove the cause, reset the alarm after confirming safety, and then resume operation. Failure to observe this caution may result in injury.

• Do not use the servo brake of the servomotor for ordinary braking. Failure to observe this caution may result in malfunction

Brand: Yaskawa

Product Name: direct drive servo motor model: sgmcs-10c3c11

Direct drive servo motor sgmcs small capacity type. Rated torque: 10N · M

Outer diameter dimension of servo motor: 175mm.

Serial encoder: 20 bit contra value type (Contra value type within 1 turn) (standard). Design sequence: models with outer diameter dimension marks of servo motor as B, C and D. Flange specification: C face, reverse load side. Optional specification: without optional.

Directly driving the load without reducer can realize strong and smooth operation from low speed to high speed

(instantaneous large torque: 6~600n · m, high speed: 250~500r/min). With 20 bit high-resolution encoder, the indexing can be carried out. It adopts hollow structure, which is convenient for wiring and piping. Example of use:

Semiconductor manufacturing equipment.

LCD circuit board manufacturing equipment. Various inspection and test equipment. Electronic parts packaging machine. IC information processor. IC inspection equipment.

All kinds of automatic machinery. robot.

Small capacity rating and specification: rated time: continuous. Vibration level: V15.

Edge resistance: DC500v, above 10m Ω. Operating ambient temperature: 0~40 °℃. Excitation mode: permanent magnet type. Installation method: flange type. Heat resistance grade: a

Edge withstand voltage: ac1500v for 1 minute.

Protection mode: totally enclosed self cooling ip42 (except for the clearance of the rotating part of the output shaft). Operating environment humidity: 20~80% (no condensation). Connection method: direct connection.

Rotation direction: CCW rotation when viewed from the load side under the forward rotation command. Servo motor sgmgh type. Rated speed: 1000r/min. Power: 0.9Kw.

Power supply voltage: three-phase ac200v. Serial encoder: 17 bit pair value. Design sequence: B.

Shaft end: taper 1/10, with parallel key Yaskawa sgmcs-10c3c11. Option: with oil seal.

High speed feed series: occasions where high-speed operation is required without load. The power supply of the main circuit and the control circuit are completely separated

In case of alarm, only the power supply of the main circuit can be turned off, which is easy to maintain. Sgmcs-10c3c11 parameter setter is built-in.

Parameters can be directly input by the servo driver body. Save wiring.

The serial encoder is adopted, and the number of encoder wiring is reduced by 112

Multi in one control: torque, position and speed control can be used by parameter switching. Servo Shenji sgmgh Yaskawa sgmcs-10c3c11. Rated speed: 1500rimin

Power: 1.3KW.

Power supply voltage: three-phase ac200v. Serial encoder: 17 bit pair value. Design sequence: for machine tool.

Shaft end: straight shaft with key and screw hole. Option: no brake oil seal.

High speed feed series: occasions where high-speed operation is required without load. The power supply of the main circuit and the control circuit are completely separated,

In case of alarm, only the power supply of the main circuit can be turned off, which is easy to maintain. Yaskawa sgmcs-10c3c11 parameter setter is built-in.

Parameters can be directly input by the servo driver body. Save wiring.

Serial encoder is adopted, and the number of encoder wiring is reduced by 1/2 compared with the original product.

Multi in one control; Torque, position and speed control can be used instead of parameter switching. Type, use good type same service unit (use good type). Large applicable motor capacity: 1.0kw Yaskawa direct drive servo motor. Power supply voltage: three-phase AC400V.

Interface: mechatrolink-iii communication command type (for rotary servo motor). Design sequence: a.

Hardware specification: dynamic brake (DB). Function: vibration function upgrade. Good type for use Σ- V-ft series

There are five servo unit models equipped with convenient functions according to different purposes

Ft001 (vibration function upgrade specification): through the enhanced vibration function, the positioning time is shortened. Yaskawa direct drive co service Motor.. Ft003 (bed force feedback function): promote the installation through the bed force control.

Ft005 (supporting the use of rotating workbench): with the function of rotating coordinates and fixed-point output, it can smooth and control the Yaskawa direct drive servo motor of the rotating workbench.

Ft006 (fixed point passing output function): the fixed point passing output (trigger) can be set without passing through the upper device.

Ft008 (support the use of value system): the value system can be built through any upper controller. Type, purpose good servo unit (purpose good).

Large applicable motor capacity: 0.4KW. Power supply voltage: single phase AC100V

Interface: mechatrolink-ii communication command type (for rotary servo motor). Design sequence: B.

Hardware specification: base mounted (standard). Function: support the use of rotating workbench. Good type for use Σ- V-ft series

According to different purposes, there are five models of the same service unit equipped with convenient functions.

Ft001 (vibration function upgrade specification): shorten the positioning time through the enhanced vibration function.

Ft003 (pressure feedback function): promote the installation of sgmcs-10c3c11 through pressure control.

Ft005 (supporting the use of travel transfer workbench): it has the function of rotating coordinates and fixed-point passing output, and can smoothly control the rotating workbench Yaskawa sgmcs-10c3c11

Ft006 (fixed point through slug out function): you can set the fixed point through output (clocking) without going through the upper installation. Et008 (supporting the first master unification Xu: the alignment system can be constructed through the one bit controller in the part chapter