Home > Products > PCB V-cut machine > 0.8-3.2 mm V-CUT aluminum plate,V-CUT Cutting Machine
0.8-3.2 mm V-CUT aluminum plate,V-CUT Cutting Machine
- 300 Set / Sets per Month
- shenzhen
- T/T L/C D/P D/A Credit Card PayPal Other Cash Escrow
Product Details
Brand Name: | YUSHUNLI | Place of Origin: | China | Model Number: | YSV-2A |
Product Description
V-CUT Cutting Machine Operating instructions:
Specification :
Product Name: PCB board v groove machine (5 pairs of plastic shaft)
Cutting width: 75mm wide vertical 380MM
Thickness: 0.8-3.2 mm
Cardboard each time V≥10 pit (above and below 10 knives)
Aluminum plate each time V≥ 5 pit (4 knife up and down)
PCB Board each time V≥ 8 pit (upper and lower knives 8)
Speed: 8 m / min
Spindle motor: 3KW inverter 3.7KW plastic shaft motor 120W close crate motor 60W
Mechanical Dimensions: 1200 mm x 980 mm x 1400 mm (W x D x H)
Weight: 145KG
Accessories: gasket set, V-CUT knife 4. Shield bearing 10, each the size of a wrench, a hex key set,
installed a turret.
Feature :
1, V-CUT aluminum shaft conveyor transport speed is adjusted to between 20 and 30, the transfer speed
of the thicker plate thinner slower speed can be adjusted faster board, under normal circumstances, the thickness was adjusted to 1.6 by 25 speed.
2, V-CUT aluminum plate conveyor speed adjustment knife arbor fastest speed, can slow the speed
V-CUT ordinary board.
3, V-CUT too ordinary board after V-CUT knife can not be used for V-CUT aluminum plate, V-CUT
aluminum plate with rough edges after the V-CUT knife can also be used for V-CUT ordinary board.
4, V-CUT aluminum plate must be cooled with alcohol, can not participate in water or water cooling.
Works Steps
1. V-CUT machine will be around and above the security guards to open the shell cover.
2. Then adjust the depth screw loosening and disassemble.
3. Taoban disassembly of the spindle drive into the middle of the wheel spindle and the spindle bearing
and relax around the upper and lower knife adjusting screw symmetry .
4. Hands hold the spindle vertically upwards heart heart out at the same time, the main axis, the knife
used (3,4) method, will be removed under the spindle.
5. Gasket fixed to the right side of the main axis of the screws removed.
6. 80-100MM first set of gauge pads into the axis, upper and lower knife shaft to the average of the
gasket.
7. Loaded blade in accordance with the requirements of MI size and installed the tool, in the loaded knife
blade when you should pay attention to the direction; the knife blade sharp outward-axis, the knife
blade tip inward axis.
8. Gasket fixed to the spindle to tighten the nut so that the blade can not be loose, and placed on the
bearing sets.
9. By (1,2,3,4) loaded action of the anti-V-CUT machine, good upper and lower knife, and a fixed screw.
V-CUT Board
1. By cutting threads tuned adjustment method of the V-CUT board. And screw fixed.
Cut Blades and shield bearing mounting method:
1. If the only knife, then knife the two bearing plates care must be to ensure that the average pressure of
the entire board.
2 . Such as twice or more, if the secant from the edge of more than 10mm, while the outer knife bearing
plate to be care. In contrast to the knife inside of the plate bearing care.
3. If the cutter is too wide the distance between the knife and the knife has to care between the bearing
plate.
Precautions :
1. Test depth (generally maintain a minimum depth of 0.3-0.4 mm thickness and the depth of the same
on both sides), trial size (size to maintain the accuracy of ± 0.05 mm) and adjust the direction of line
drawings or forming a model for the direction.
2. Check for exposed copper, wound line, V-cut, straight-line is offset, rough.
3. Board's attention to take place the way a good tune after the board should be put in the same
direction.
4. Need to work with masks and gloves in order to avoid dust inhalation mouth.
5. Blade thickness: 2.4mm; bearing thickness: 11.9mm.
6. Production of both sides of the board must be as straight, parallel to the length of more than 80mm
above.
7. Bearing shield such as dust, debris stuck, which may result in non-linear or thread-cutting distortions.
8. Workpiece conveyor track must be kept clean and should be polished often.
9. Moderate elastic wheel drive, oil and scratches do not dip. 10. Films for cutting super hard tungsten steel easy to break, not a collision or fall.
11. Clearance gauge pads placed on the cabinet in accordance with the specifications, do not brush or
excessive percussion gongs, the thickness tolerance of ± 0.015mm.
12. 7 gear oil once the sky, and other mechanical parts required to be kept clean and dry.
Maintenance:
1. End of production for each plate using a sharp suction machine to machine panels
Siphoning gray.
2. End time of each production to be down to the tool spindle at the heart rags soiled with oil rubbed on
the point on the axis, to prevent rust
3. Removed per blade and V-CUT shield with anti-rust bearings no maintenance
4. To drive every day to clear out the rubbish
5. Weekly by the maintenance department to assist the V-CUT refueling on a rotational slide area.
Contact Us
- YUHS Electronic Technology Co.,Ltd
- Contact namesunny
- Phone86-18476810780
- AddressChang'an Town Dongguan,Guangdong
- BENTLY 1900/65A-00-04-01-00-00 Device monitor
- ABB XVC768101 3BHB007211R101 power interface Module
- ABB LD800HSE communication interface module
- ABB UAC389AE02 HIEE300888R0002 Excitation control module
- ABB UAC383AE01 HIEE300890R0001 Control board
- ABB PPC907BE101 3BHE024577R0101 frequency converter
- GE ESP10B Flow and pressure controller
- GE ESM10A Ethernet communication module
- ABB DSAO120A 3BSE018293R1 Excitation conditioning
- ABB KSD211B 3BHE022455R1101 Coupling device unit
- HONEYWELL 05701-A-0302 Single channel control card
- ABB XVC768115 3BHB007211R115 Remote IO devices
- ABB XVC767AE105 3BHB007209R0105 Drive power module
- BENTLY 3500/22M 138607-02 Transient Data Interface Module
- ABB 5SHY5055L0002 3BHE019719R0101 GVC736BE101 Thyristor
- BENTLY 3500/42M 140734-02 Vibration monitoring system
- BENTLY 3500/32 125712-01 Four channel relay module
- BENTLY 3500/20 125744-02 condition monitor system
- ABB KUC755AE117 3BHB005243R0117 Excitation drive control module
- BENTLY 1900/65A-00-00-02-00-01 Vibration monitoring and analysis module
- VIBRO-METER 200-510-076-114 200-510-111-034 VM600 MPC4 Vibration monitoring instruments
- GE RS-FS-9001 362A1052P404 flame sensor Please contact me if you need product images
- KONGSBERG RMP201-8 sensor
- EMERSON MVME6100 single board computer
Popular Searches
- lightning conductor
- Copper Lightning Rod
- earthing system
- transmission rod
- 11 kv lightning arrester
- Copper Clad Steel Ground Rod
- static eliminator
- anti static device
- lightning connector
- plasma tv lift
- mtl safety barrier
- copper earthing bar
- copper earthing rods
- electrical earth rod
- earthing material
- Clad Steel Ground Rod
Find Similar Products By Category
- Electrical Equipment & Supplies > Other Electrical Equipment
- Buy on GoldSupplier.com
- How to Buy
- Browse by Catagories
- Browse by Hot Regoins
- Private Sourcing Events
- Sell on GoldSupplier.com
- How to Sell
- Post Products
- Manage Products
- Manage Groups
- About
- About Us
- Link to Us
- Contact Us
- Sitemap
- Please Enter your Email Address
- Please enter the content for your inquiry.
We will find the most reliable suppliers for you according to your description.
Send Now-
sunny
Welcome to my shop! Glad to serve you!Please send your question!
Your message has exceeded the limit.
Your message has exceeded the limit.
-
-
Your inquiry content must be between 20 to 5000 characters.Send Now.
-
Please input the mailbox.
-