- Guangxi COHO Electromechanical Co. Ltd..
- China Manufacturer with main products:Stop valves ,Danfoss valves ,EMERSON valves ,Servo Valves ,Pressure Sensor ,Level Switch ,Check Valves ,Motor Operated Valves ,Liquid Level Sensor ,Liquid Level Regulating Valves ,Solenoid Valves ,Electric Expansion Valves
Home > Products > Servo Valves > Danfoss Pilot-operated servo valve Types PM1-32-40,PM3-65-80,PM3-100-150
Danfoss Pilot-operated servo valve Types PM1-32-40,PM3-65-80,PM3-100-150
- 115 Unit / Units per Month
- Guangzhou
- PayPal
- 3 days
Product Details
Brand Name: | Danfoss | Place of Origin: | Denmark | Model Number: | PM1-32-40,PM3-65-80,PM3-100-150 |
Material: | Other, carbon steel | Application: | General | Structure: | Regulating |
Standard or Nonstandard: | Standard | Pressure: | Medium Pressure | Power: | Solenoid |
Port Size: | 20-150mm | Media: | Gas | Temperature of Media: | Normal Temperature |
Product Description
Danfoss Pilot-operated servo valve Types PM1-32-40,PM3-65-80,PM3-100-150 Technical data
Refrigerants
Applicable to all common non-flammable refrigerants, including R717 and non-corrosive gases/liquids dependent on sealing material compatibility.
Flammable hydrocarbons are not recommended. The valve is only recommended for use in closed circuits. For further information please contact Danfoss.
Temperature range
PM: –60/+120°C (–76/+248°F)
Pressure range
PM: The valves are designed for a max.
working pressure of 28 bar g (406 psi g).
Technical data
The PM 3 can be used in suction, liquid, hot-gas and liquid/vapour lines.
The PM 3 regulates the flow of the medium by modulation or on/off function, depending on the control impulse from the screwed-on pilot valves. The PM 3 has three connections for pilot valves: two in series, marked “S I” and “S II”, and one in parallel with these two, marked
“P”, see figs. 2 and 3.Schematic examples of pilot valves connected to the PM can be seen in figures 5, 6, 7, and 8.If only two pilot valves are necessary for the function required, the third pilot connection must be sealed with a blanking plug (see fig. 5). A blanking plug is supplied with the valve.
Regulating range
Dependent on pilot valves.
Opening differential pressure (∆p)
The PM main valve requires a minimum opening differential pressure of 0.07 bar (1 psi) to begin to open and 0.2 bar (2.8 psi) to be completely open.
Note: The valve opens when differential pressure against the direction of flow occurs.
Danfoss Pilot-operated servo valve Types PM1-32-40,PM3-65-80,PM3-100-150 Installation
Flange set for the PM is delivered separately. The valve must be installed with the arrow in the direction of the flow and the top cover upwards (fig. 4). The top cover can be rotated 4 × 90° in relation to the valve body.
The valve is fitted with a spindle for manual opening.If an external pilot valve is used, the pilot line must be connected to the upper side of the main line so that any dirt and oil from the plant will not find its way into the pilot line.
If the PM 3 is to be used as a solenoid valve in a liquid line, external control pressure cannot be recommended because it can cause liquid hammer.
The valve is designed to withstand a high internal pressure. However, the piping system should be designed to avoid liquid traps and reduce the risk of hydraulic pressure caused by thermal expansion. It must be ensured that the valve is protected from pressure transients like “liquid hammer” in the system.
Danfoss Pilot-operated servo valve Types PM1-32-40,PM3-65-80,PM3-100-150 Welding
If using welding flanges, only materials and welding methods, compatible with the flange material must be welded to the flanges. The flanges should be cleaned internally to remove welding debris on completion of welding and before the valve is inserted.The valve housing and flanges must be free from stresses (external loads) after installation. PM valves must not be mounted in systems where the outlet side of the valve is open to atmosphere. The outlet side of the valve must always be connected to the system or properly capped off, for example with a welded-on end plate. Colours and identification The PM valves are Zinc-Chromated in the factory. If further corrosion protection is required, the valves can be painted. Precise identification of the valve is made via the ID plate on the top cover. The external surface of the valve housing must be prevented against corrosion with a suitable protective coating after installation and assembly. Protection of the ID plate when repaintingthe valve is recommended.
Danfoss Pilot-operated servo valve Types PM1-32-40,PM3-65-80,PM3-100-150 Maintenance
Service
The PM valves are easy to dismantle and most of its parts are replaceable. When the bottom cover is removed, the strainer can be taken out for cleaning.Do not open the valve while the valve is still under pressure.
- Check that the gasket has not been damaged. Ideally, the gasket should be replaced.
- Check that the spindle is free of scratches and impact marks.
- If the teflon ring has been damaged, theparts must be replaced.
Assembly
Remove any dirt from the body before the valve is assembled. Check that all channels in the valve are not blocked with particles or similar.
Tightening
Tightening torques See fig. 1 and table 1. Always carry out this operation when the manual operation device has been in use (see fig 9)
1. Remove the cap (A) and tighten the spindle (B) anticlockwise with 8 Nm
(5.9 lb/ft)
2. Remount the cap (A) and tighten it clockwise with 8 Nm (5.9 lb/ft)
Use only original Danfoss parts, including packing glands, O-rings and gaskets for replacement. Materials of new parts are certified for the relevant refrigerant.In cases of doubt, please contact Danfoss.Danfoss accepts no responsibility for errors and omissions. Danfoss Industrial
Refrigeration reserves the right to make changes to products and specifications without prior notice.
Contact Us
- Guangxi COHO Electromechanical Co. Ltd..
- Contact nameko
Danfoss valves | EMERSON valves | Stop valves | Thermal Expansion valves |
Solenoid Valves | Sensors | Safety Relief Valves | Motor Operated Valves |
Servo Valves | Check Valves | Level Switch | Electric Expansion Valves |
- AST/OPC solenoid valve coil 300AA00086A for power generation
- globe valve SHV6.4 for power station
- temperature Regulating valve LWH-ZG1/2 for power plant
- Inclined groove three-way distributor Pneumatic electric circular three-way valve XZ500 distributor
- sealing oil floater tank float valve FY-40 for power generation
- Sinro Motorized Valve SR04GB32046B4 for power station
- servo valve G761-3034B for power plant
- Bare Stem Fluorine Lined Butterfly Valve
- Alpha split isolated valve ABvalve OEB5level
- AlphaAB valve split butterfly valve
- AB valve Split Isolated Valve split butterfly valve
- Manual Operated Wafer Type PTFE Lined Butterfly Valve
- Pneumatic PTFE Lined Diaphragm Valve
- solenoid valve 22FDA-F5T-W220R-20 for thermal power plant
- solenoid valve J-110VDC-DN10-Y/20H/2AL for power generation
- ealing oil float tank float valve BYF-40 for power station
- Air transfer chute three-way to curved four-way distributor valve
- B500 Air chute pneumatic closure valve Inflatable manual plugboard valve
- Aseptic transfer αβ Valve manufacturer sealed feeding powder transfer AB valve
- Manufacturer of high activity powder transfer AB valve split type butterfly valve
- makeup water solenoid valve K25FJ-1.6PA2 for power generation
- AST/OPC solenoid valve 0508.919T0301.AW027 for power plant
- X43T-10Cast iron copper core two-way flanged plug valve
- PTFE Lined Globe Valve
Popular Searches
Find Similar Products By Category
- Mechanical Parts & Fabrication Services > Valves
- Buy on GoldSupplier.com
- How to Buy
- Browse by Catagories
- Browse by Hot Regoins
- Private Sourcing Events
- Sell on GoldSupplier.com
- How to Sell
- Post Products
- Manage Products
- Manage Groups
- About
- About Us
- Link to Us
- Contact Us
- Sitemap
- Please Enter your Email Address
- Please enter the content for your inquiry.
We will find the most reliable suppliers for you according to your description.
Send Now-
ko
Welcome to my shop! Glad to serve you!Please send your question!
Your message has exceeded the limit.
Your message has exceeded the limit.
-
-
Your inquiry content must be between 20 to 5000 characters.Send Now.
-
Please input the mailbox.
-