Contact Platform Support
Help CenterWire Fire Resistance Test Machine, (FTech-IEC60331A)
Related Products
-
Motor Accessories Combustion Testing Machine, Fmvss 302NegotiableMOQ: 1 Set -
Room Corner Test Machine, ISO 9705, En 14390NegotiableMOQ: 1 Set
-
Nbs Smoke Density ChamberNegotiableMOQ: 1 Set
-
Fire Testing Equipment Cone CalorimeterNegotiableMOQ: 1 Set
-
En 136 Full Face Masks Fire Test MachineNegotiableMOQ: 1 Set
Description:
Fire-resistant cable refers to the cable that can keep a safe running time in the case of flame combustion.
TESTECH Fire Resistance Tester is designed according to the requirements of IEC60331-11,and used to obtain the refractory characteristics of a fire resistant cable or optical cable under flame conditions.
Model:FTech-IEC60331A
User' s Experience:
1, This cabinet is made of stainless steel, anti-smoke and gas corrosion.
2, The control system is designed with a high degree of automation, automatic ignition, temperature and time digital display, convenient to observe and record, stable and reliable.
Standards
• IEC 60331 Part 11
• IEC 60331 Part 21
Main Features:
1, All fixtures are made of stainless steel;
2, The burner is a belt type propane blowtorch with a Venturi mixer, and the burner nozzle is length 500mm, width 15mm;
3, Those burning holes are staggered into 3 rows, and the front width is 15mm, holes diameter is 1.32mm and these holes center distance is 3.2mm;
5, One end of the specimen holder is equipped with a clamp to fix the sample, and the other end is convenient for heat transfer along the longitudinal specimen;
6, The cable sample is supported by two metal rings, and the middle length of the two rings is about 300mm;
7, An inner diameter of the sample supporting metal rings is 150mm, and the cross-sectional diameter of the ring is 10 ± 2mm.
8, The position of the burner torch from burning the bottom is not less than 200mm, and not less than 300mm from the tank wall.
Combustion System:
1, Independent standard electrical control platform;
2, With intelligent detection function, when a short circuit in the sample during the test, automatic alarm and turn off the fire source.
3, Fuse current in the experimental circuit is 2A;
4, The sample is applied to power of AV 100V ~ 1000V adjustable;
5, The time can be set free for the fire, the time recommended by standards is 90min.
Device parameters:
1, Voltage: AC 380V 3-phase, 50 / 60Hz, 30A;
2, The input voltage 0 ~ 1000V; can be adjusted;
3, The breakdown current is 2A;
4, Maximum power: 5000VA;
5. Timer: 0 ~ 999min
6, The flame temperature of 0 ~ 1100 ºC adjustable;
7, The test load current is 0.25A, can be adjusted;
Send Inquiry to This Supplier
You May Also Like
-
(Protective Clothing) Protection Against Radiant Heat Test MachineNegotiableMOQ: 1 Set
-
Needle Flame Test Machine, IEC60695-2-2 (FTech - IEC60695)NegotiableMOQ: 1 Set
-
ISO 6941 Fabric Vertical Flame Spread Test MachineNegotiableMOQ: 1 Set
-
Protective Clothing Flame Spread Test Machine, BS En ISO 15025NegotiableMOQ: 1 Set
-
Nfpa 701 Curtain Flame Propagation Test MachineNegotiableMOQ: 1 Set
-
Direcct Flame Impingement Test Machine, BS 476-12NegotiableMOQ: 1 Set
-
En 13823 Single Burning ItemNegotiableMOQ: 1 Set
-
Nfp92-501 Thermal Radiation Dripping Test MachineNegotiableMOQ: 1 Set
-
En ISO 1716 Bomb CalorimeterNegotiableMOQ: 1 Set
-
Building Material Radiant Panel Test Machine,NegotiableMOQ: 1 Set
