sintered filter service attitudefilter equipment and accessoriescompressor filter

Henan Uters International CO.,LTDwas established in Henan Free Trade Zone Zhengzhou Area (Jinshui) Garden Road 107, is set COMPRESSOR FILTER,Metal Filters,Stainless steel filter,HYDRAULIC OIL FILTER,Coalescer filter and other functions as one , with a strong comprehensive strength of the modernizationpleated filterx1dd023enenterprise groups. Henan Uters International CO.,LTD adhere to ｃｒｅａｔｅ wealth for the community, ｃｒｅａｔｅ quality for the customer as the core values of enterprises, pay attention to social responsibility, look to be a good corporate citizen as an important part of our corporate culture.

UTERS
Working principle of filter

When the filter is working, the filtered water will enter the water inlet, flow through the filter screen, and enter the pipeline through the outlet to process the users required process, and the particulate impurities in the water will be trapped in the filter screen. This constant cycle, more and more particles trapped down, filtering speed more slowly, and imported into the sewage is still Everfount, filter holes will become increasingly smaller, resulting in pressure difference between inlet and outlet, when large difference reaches the set value, the differential pressure transmitter electrical signals will be transmitted to the controller, control system start the drive motor to rotate through the transmission shaft assembly drives the sewage outfall, at the same time open, discharged from the sewage outfall, when the filter cleaning is finished, the pressure dropped to the minimum value, the system returns to the initial filter, the normal operation of the system. The filter is composed of a shell, a multiple filter core, a backwashing mechanism, and a differential pressure controller. The diaphragm of the shell is divided into two chambers, the upper cavity and the lower one. The upper chamber is equipped with a plurality of filter cores, so that the filter space is fully reduced, and the volume of the filter is significantly reduced. The backwashing chuck is installed in the lower cavity. When working, the emulsion entrance into the filter chamber, and the inner baffle hole into the filter. The impurities which are larger than the filter core are intercepted, and the net liquid goes through the gap to the upper chamber, and then it is sent out from the exit. The filter uses high strength wedge-shaped filter net to automatically clean the filter core through pressure difference control and timing control. When the impurity in the filter is accumulated on the surface of the filter element, causing the inlet and outlet pressure difference to increase to the set value, or when the timer reaches the preset time, the electric control box sends out a signal to drive the backwashing mechanism. When the backwash suction port and the filter is imported when the sewage valve is opened, the pressure relief drainage system, the sucker and the inside of the filter is a relative pressure below the negative pressure zone of the filter lateral pressure, forcing some clean circulating water from the outside into the inside of the filter cartridge, adsorption of impurities particles in the filter on the inner wall with the water flow into the Rang disc and is discharged from the drain valve. A specially designed filter makes the interior of the filter produce a jet effect, and any impurity will be washed away from the smooth inner wall. When the pressure difference between the inlet and outlet of the filter is restored to normal or the timer setting time is over, during the whole process, the material is not broken down, and the water consumption of backwashing is less, which realizes continuous and automatic production. The filter is widely used in the fields of metallurgy, chemical industry, petroleum, papermaking, medicine, food, mining, electric power and urban water supply. Such as industrial waste water, circulating water filtration, emulsion regeneration, waste oil filtration treatment, continuous casting water system and blast furnace water system in metallurgical industry, and high pressure water descaling system for hot rolling. It is an advanced, efficient and easy to operate fully automatic filter.
The water to be treated by the filter is entered into the body from the inlet, and the impurities in the water are deposited on the stainless steel filter network, resulting in the pressure difference. The pressure difference of the inlet and outlet is monitored by the differential pressure switch. When the pressure difference reaches the set value, the electronic control device gives the hydraulic control valve to drive the motor signal. Equipment installation, debugging by the technical staff, filtration time and cleaning time conversion, the water to be treated into the body from the water inlet filter to begin work, when it reaches the preset cleaning time, electric controller for hydraulic control valves, motor drive signal, triggered a series of actions: the motor drives the rotation of the brush to clean. At the same time filter, the control valve is opened to discharge, the whole cleaning process needs to last only tens of seconds, when cleaning at the end, close the control valve, the motor stops rotating, the system returned to its initial state, began to enter the next filtering process. The inner part of the filter is mainly composed of coarse filter screen, fine filter screen, suction pipe, stainless steel brush or stainless steel suction nozzle, sealing ring, anticorrosive coating, rotating shaft and so on.
A filter is formed by separating the container into the upper or lower chamber with the filter medium. The suspension is added to the upper cavity. Under pressure, it enters the lower cavity through filtration medium and becomes filtrate. Solid particles are trapped on the surface of filtering medium to form filter residue (or cake). During the filtration process, the filter slag layer gradually thickened, the resistance of liquid through the slag layer increased and the filtration speed decreased. When the filter chamber is filled with filter residue or filtration speed for too small hours, the filter is stopped, filter slag is cleared, and the filter media is regenerated to complete a filtration cycle. The liquid must overcome the resistance by filtering the slag layer and the filter medium, so there must be pressure difference on both sides of the filter medium, which is the driving force for filtering. The pressure difference can accelerate the filtration, but the pore of the filter medium is easily blocked in the large pressure difference after the pressure difference, and the filtration is slowed down.
There are 3 kinds of filtration methods: filtration of slag layer, deep filtration and sieve filtration.
Filter slag filter: the filtration medium at the initial stage of filtration can only intercept the large solid particles, and the small particles follow the filter medium with the filtrate. After the formation of the initial slag layer, the slag layer plays a major role in the filtration, and the large and small particles are all intercepted, such as the filter of the plate frame filter press.
(2) deep filtration: the filter medium is thicker, and the solid particles in the suspension are less, and the particles are smaller than the filter media. When the particles are filtered, the particles are adsorbed in the channel, such as the filter of porous plastic pipe and sand filter.
Filtration and filtration: the solids retained by filtration are greater than those in the filtration medium, and no solid particles are adsorbed inside the filtration medium, for example, the rotary filter screen can filter coarse particles in the sewage. In the actual filtering process, the three ways are often at the same time or successively.
is focused on Quality assurance wound filter, Supply stability COMPRESSOR FILTER, Sintered filter the importance of, Good quality after-sales service wound filter and other projects. even though in the rapid development of the project ,UTERS always stressed the balance between external opportunities and internal management, attaches great importance to the core competitiveness of enterprises to cultivate and shape. Our company take the value of customer service as the core competitiveness of enterprises, adhering to the honesty and integrity , the pursuit of excellence, respect individual for the corporate spirit, and strive to provide customers with integrity and reliable Sintered Filter.

The integrity, strength and prodzationuct quality of Henan Uters International CO.,LTDhas gain highly industry recognition. Welcome friends from all walks of life come for visit, guidance and business negotiations. For more information please visit: