Aluminum Alloy Ageing Furnace Quenching

Used for aluminum alloy extrusion profiles aging treatment, promote the strength, aluminum alloy castings solid solution process after the limitation in heat treatment. Aluminum alloy ageing furnace is used to eliminate the aluminum alloy material after the special equipment of preheating vegerable. Objective to reduce the stress concentration of the aluminum alloy material, reduce the deformation of the aluminum alloy material, is the production of aluminum alloy products manufacturer ideal equipment.

Features:

1, lin-ings adopted the fiber structure, improve the furnace thermal insulation performance, save energy and reduce the production cost;

2, electric furnace with hot air circulation device, improve the furnace temperature evenness;

3 for side, door open, the operation is convenient;

4, electric furnace with car with material of the workpiece loading and unloading operation is convenient;

5, electric furnace use PID control procedures section thermometer table temperature control, automatic control of electric heating speed;

6, electric furnace with chain protection device, can prevent for wrong operation fault and from the accident;

7, no pollution, and environmental benefits.

Structure introduction:

By electric furnace, heating device structure, control system components.

Furnace shell the frame of steel welding forming, internal and external wall all use high quality cold-rolled steel sheet production, heat distortion coefficient little lined with the aluminum silicate refractory fiber needle-punched cotton for insulation and heat preservation material, reduce the temperature of the furnace wall.

Furnace door furnace shell also adopts steel welding be framework, outside wall to also use cold rolled steel plate making, lined with also USES guisuanlu: refractory fiber needle-punched cotton as heat insulation and heat preservation material.

Around the oven are embedded rubber asbestos pan-gen, door of the oven and turned the rubber asbestos pan-gen adhere to ensure no quantity of heat to send out.

Heating element using belt electric heating element, decorate in the furnace respectively on both sides, the material is 0 Cr25AL5 alloy and long service life.

In order to ensure the steady furnace evenness, electric furnace has the ventilator device and ventilation system, the ventilator devices on top of furnace, using 1 Cr18Ni9Ti heat resistant steel fan made centrifugal wind leaf. Ventilation system guided by the boards and the windshield of plate, guide the wind in the top board install furnace, a guide on the wind trough. When open fan, fan throw from the wind, the wind blows to the slot evenly on both sides of the furnace heating element, through the windshield of the lower plate guide to blow in the furnace tuyere, and again from the bottom of the draught fan the suction fan inside, then throw & # 8226; & # 8226;& # 8226;& # 8226;& # 8226;& # 8226;And so reciprocating cycle will heater heat generation into the chamber, to make the work is heated evenly.

Temperature control system adopts PID zero trigger thyristor, intelligent temperature control list. The other by Shanghai dahua YiBiaoChang more automatic recorder and record temperature over temperature alarm dual control, ensure the not super temperature.

The mechanical transmission part adopts electric chain control, namely door open automatically cut off after the ventilator device and heating a power supply. Furnace door closed in place, can through to the ventilator device and element of power supply, prevent wrong operation fault and accidents

Aging furnace used in aluminum alloy extrusion profiles aging treatment, promote the strength, aluminum alloy castings solid solution process after the limitation in heat treatment. Aluminum alloy ageing furnace is used to eliminate the aluminum alloy material after the special equipment of preheating vegerable. Objective to reduce the stress concentration of the aluminum alloy material, reduce the deformation of the aluminum alloy material, is the production of aluminum alloy products manufacturer ideal equipment.

Features:

1, lin-ings adopted the fiber structure, improve the furnace thermal insulation performance, save energy and reduce the production cost;

2, electric furnace with hot air circulation device, improve the furnace temperature evenness;

3 for side, door open, the operation is convenient;

4, electric furnace with car with material of the workpiece loading and unloading operation is convenient;

5, electric furnace PID control procedures section thermometer table temperature control, automatic control of electric heating speed;

6, electric furnace with chain protection device, can prevent for wrong operation fault and from the accident;

7, no pollution, and environmental benefits.

Structure introduction:

By electric furnace, heating device structure, control system components.

Furnace shell the frame of steel welding forming, internal and external wall all use high quality cold-rolled steel sheet production, heat distortion coefficient little lined with the aluminum silicate refractory fiber needle-punched cotton for insulation and heat preservation material,