Contact Platform Support
Help CenterHigh Quality 150w Co2 Laser Cutting Power Source
Related Products
-
High Power Laser Power Supply HY-T150 for CO2 Laser Tubes Above 120W From Different FactoriesUS$ 170 - 180MOQ: 1 Piece -
HY-W120 for CO2 Laser Tubes Below 110W From Different Factories, Support 110V 220V Input Voltage, Wide Range of Input VoltageUS$ 160 - 170MOQ: 1 Piece
-
HY-T80 Universal Laser Power Supply for 80w 1600mm or 1250mm From Different FactoriesUS$ 120 - 130MOQ: 1 Piece
-
HY-T60 Universal Laser Power Supply for All Kinds of CO2 Laser Tubes, 30W/40W/50W, Acrylic Material Laser Engraving MachineUS$ 100 - 110MOQ: 1 Piece
-
HY-T50 Universal Laser Power Supply for All Kinds of CO2 Laser Tubes, 30W/40W/50W, Acrylic Material Laser Engraving MachineUS$ 90 - 100MOQ: 1 Piece
co2 laser 130w power source
for glass laser tube economy model
100w-150w
input voltage AC220V OR AC110V
AC frequency 47-440Hz
max output voltage DC50kv
max output current DC38mA
Input Voltage |
Input Voltage |
AC220V or AC110V |
|
|
AC Frequency |
47-440Hz |
|
|
Cold surge current |
≤60A(AC220V input) |
≤60A(AC220V input) |
|
Leak current |
≤0.7mA(AC220V input) |
≤0.7mA(AC220V input) |
Output |
Max output Voltage |
DC50KV |
|
|
Max Output current |
DC 38mA |
|
Efficiency |
when≤92%load down |
||
Time no-failure |
≤10000 hours |
||
Response speed |
≤1ms(the time from output of switch signal to 90%of initial setting current) |
||
Control port |
TLL electricity level switch control, valid electricity has high/low level choices |
||
Vollage-resisting |
Input-Output ,input-machine hull: 1500V 10mA 60s AC output cathode and machine hull connection |
||
Protection |
Can be used an opening way in a short time(request the outer shell be good to connent the ground avoid arcing between anode and machine hull connection in the machine) |
||
Vsage environment |
Work temperature:(-10-40)°C.Relative humidity:≤90% |
||
Cooling Type |
The compuisive air cooling |
||
size |
L×W×H=350×240×95(mm) |
||
Weight |
6kg |
||
Caution:
1.Water cooling system should be working properly when switching on laser
device.
2.Circuit of high voltage output should not be open! (High voltage output
terminals(positive and negative poles) shall be properly connected to positive
and negative poles of laser device, respectively.)
3. Attentions should be given to avoid any electric shock after the power
supply being switched off.
4. Well-grounded three-pole receptacle should be used to supply power to HYHVCO2/
X power supply. The enclosure should be well grounded to avoid electric
shock.
Send Inquiry to This Supplier
You May Also Like
-
1-5mw Mini Red Laser Module for Laser Alignment and Gun Laser SightUS$ 1 - 20MOQ: 10 Pieces
-
SUDA Mini Laser Garment Machine CNC LASER CUTTER---SL4030NegotiableMOQ: 1 Set
-
980nm ir Test Card of Infrared Laser(HT582)US$ 30 - 100MOQ: 100 Pieces
-
Laser Tube 100wUS$ 50 - 300MOQ: 6 Pieces
-
Laser 532nm, 5mw Dot Laser ModuleUS$ 7.6 - 8.9MOQ: 3 Pieces
-
RECI CO2 Laser Tube 100w 10000 Hours Working LifeUS$ 560 - 700MOQ: 1 Piece
-
New Original SF-HD80US$ 0.1 - 0.12MOQ: 1 Piece
-
YFL-2000 Portable Fiber Laser,Extreme Environment "Mobile Operations"!NegotiableMOQ: 10 Units
-
Supply of Laser Heads, Output Heads, Laser Input Heads, Coupling Heads With High Efficiency and High Precision FOL-30KSUS$ 350MOQ: 1 Piece
-
10046088 Refractive Lens Resonant Cavity LensesUS$ 2900 - 3500MOQ: 1 Piece
