Contact Platform Support
Help Center100 Bar High Pressure Multistage Sea Water Pump
Related Products
-
Centrifugal High Pressure Boiler Feed Multistage Water PumpUS$ 300 - 6,800MOQ: 1 Set -
High Pressure Horizontal Centrifugal Multistage Free Standing Heat PumpUS$ 300 - 19,000MOQ: 1 Set
-
High Pressure Multistage Boiler Hot Water Heater Booster PumpsUS$ 300 - 6,800MOQ: 1 Set
-
High Pressure Centrifugal Multistage Boiler Feed Water PumpUS$ 300 - 9,000MOQ: 1 Set
-
Heavy Duty Water Pump Stainless Steel Multistage Horizontal PumpUS$ 360 - 18,000MOQ: 1 Set
100 Bar High Pressure Multistage Sea Water Pump
♠♠♠♠♠ GENERAL OVERVIEW ♠♠♠♠♠
General overview about 100 Bar High Pressure Multistage Sea Water Pump
QDG model middle and low pressure seawater pump is applicable to transport medium with temperature of not higher than 105℃, and is also applicable for small boiler water supply or transporting medium similar to hot water.
QDG model hypo high pressure seawater pump is used to transport medium with temperature of not higher than 160℃, and is also applicable for small boiler water supply or transporting medium similar to hot water, also sea water.
Model QDG seawater pump is a horizontal multistage centrifugal water feed boiler pump and suitable for transporting pure water (with the contained foreign matters' content less than l % and graininess less than 0. 1mm) and other liquids of both physical and chemical natures similar with those of pure water.
♠♠♠♠♠ APPLICATION ♠♠♠♠♠
Application about 100 Bar High Pressure Multistage Sea Water Pump
Type QD(G) high pressure seawater pump are used for feeding high pressure boiler or pumping high pressure clean water.
The temperature of pumped media is not more than 170℃.
♠♠♠♠♠ PERFORMANCE PARAMETER ♠♠♠♠♠
Peformance parameter of 100 Bar High Pressure Multistage Sea Water Pump
Range of capacity: 120-1100m3/h
Range of total head:967- 2500m
♠♠♠♠♠ CONSTRUCTION DRAWING ♠♠♠♠♠
Construction drawing about 100 Bar High Pressure Multistage Sea Water Pump
The boiler pump is supported by both ends, and casing portion is sectional.
Connected with motor by flexible coupling For rotating direction, viewing from the motor end.
♠♠♠♠♠ CONSTRUCTION FEATURES ♠♠♠♠♠
Construction features about 100 Bar High Pressure Multistage Sea Water Pump
1. The seawater pumps are sectional casing,multistage centrifugal pumps. The suction casing, stage casing and discharge casings are rigidly held together by tie bolts. The joints between these casings are primarily sealed by means of metal-metal contact. Simultaneously,O-rings are used as auxiliary seals.
2. The shafts of these pumps are sealed by soft-packing and cooling water. Mechanical seal can be used according to the client's requirement.
3. The rotating assembly is supported by sliding bearings on both ends of the pump shaft. Bearings of pump are forced-lubricated. The oil system is equipped for type QD(G) pump The axial thrust of rotor is balanced by balance disc. And the thrust bearing is also provided which is sed to bear residual axial force caused by the change of working conditions.
The assembly quality of the boiler pump will result in a notable affection to the performance and the running stability of it and can not be guaranteed unless the technical requirements in the drawings are strictly followed in the assembly, such as on the alignment between the centers of the impeller’s outlet and the guide vane's inlet. the uniform values of the sealing intervals of both rotor and stator portions etc.
Covering angle and central line posit ion adjustment. check the equipments at least in the fol lowing three periods and take adjustment:
The first time, both seawater pump and foundation are secured while the motor is not.
The second time, both pump and motor are secured while the bolts on the suck-in and spitting pipeline flanges are not.
The third time is in 24 hours after the pump starts running,then secure both pump and motor
♠♠♠♠♠ ATTENTIONS ♠♠♠♠♠
Attentions about 100 Bar High Pressure Multistage Sea Water Pump
The seawater pump is allowed to run within the set parameter range only.
The pump is not allowed to run with the spitting valve closed or closed to a little opening, or it will be caused heated and duration lowered. Each pump is required to run under the special parameters so as to guarantee the flow of it if mounted in a parallel system.
The pump can not run with the suck-in valve closed, or it may be dried moving to cause parts damaged.
The medium the pump transports can not contain air or gas, or both flow and head of the pump may not be accurately measured and, meanwhile, grinding maybe produced to damage parts.
This pump is not allowed to transport any material with grains, or both pump efficacy and part duration may be lowered.
To keep the boiler pump in a high effective and stable work, it must be often repaired, the items of repair and the interval between every repair depend on the working condition and running state of it.
♠♠♠♠♠ DRIVER ♠♠♠♠♠
Driver about 100 Bar High Pressure Multistage Sea Water Pump
The seawater pump is driven by the motor through the coupling The gear, membrane coupling and hydraulic coupling can be used according to client's requirements. The pump can be driven by turbine or motor.The rotating direction of pumps are clockwise when viewed from the driving end.
♠♠♠♠♠ CURVE CHART ♠♠♠♠♠
Curve chart about 100 Bar High Pressure Multistage Sea Water Pump
♠♠♠♠♠ PERFORMANCE DATA SHEET ♠♠♠♠♠
Performance data sheet about 100 Bar High Pressure Multistage Sea Water Pump
♠♠♠♠♠ FAQ ♠♠♠♠♠
FAQ about 100 Bar High Pressure Multistage Sea Water Pump
1. The completed supply of seawater pump group includes:
1 Water supply pump, pre-pump and its inlet filtering screen
2 Motor
3 Hydraulic coupler and oil cooler for both working and lubricating oils
4 Check valve at the outlet of the water supply pump
5 Minimum flow device : includes recycling valve, stop valve and flow measurer
6 Clutch and other accessories
7 Oil thin station
8 Of which the motor, recycling valve, hydraulic coupler, oil thinning station, check valve,pre-pump, stop valve and flow measurer can also be purchased by clients and this Co.will be in charge of technical coordination.
2. Please provide the following parameters when to order the 100 Bar High Pressure Multistage Sea Water Pump
1. Flows at the outlet of the water supply pump and the tap (boosting class)
2. Pressures(or the pump group's head) at the outlet of the water supply pump and the inlet of the pre-pump
3. Water supply temperature
4. Pump group's type(Diesel engined or electric pump)
5. The installation dimensions are to be provide at order upon the contract requirement
♠♠♠♠♠ AN PUMP HISTORY ♠♠♠♠♠
♠♠♠♠♠ AN PUMP OVERVIEW ♠♠♠♠♠
♠♠♠♠♠ PRODUCT TEST ♠♠♠♠♠
♠♠♠♠♠ MAIN FACILITES ♠♠♠♠♠
♠♠♠♠♠ MAIN PRODUCT LINES ♠♠♠♠♠
Main product lines
An Pump Machinery manufactured slurry pumps, sewage pump, water pump, chemical pumps, fire pumps, irrigation pumps and other products are exported to over 90 countries around the world. The application covers many fields, such as dressing ship, tailings transportation, mining pumps, steel & power desulphurization, boiler feed water, construction, irrigation, water conservancy facilities, sewage treatment.
♠♠♠♠♠ ENGINEER DEPT ♠♠♠♠♠
Engineer department
Experienced technical personnel is the powerful guarantee for quality products of slurry pumps, sewage pump, water pump, chemical pumps, fire pumps, irrigation pumps.
An Pump Machinery technical team set up five R & D teams:
hydraulic engineering, water pump structure, new materials research and development, casting, molding etc.
Except the commonly used CAD and other design software, the technical teams also use CAPP computer-aided industrial design and CFD hydraulic design software.
♠♠♠♠♠ MANUFACTURING PROCESS ♠♠♠♠♠
Manufacturing process
♠♠♠♠♠ AN PUMP SERVICES ♠♠♠♠♠
Our services about 100 Bar High Pressure Multistage Sea Water Pump
Offer pump solution, design, manufacturing, and after-sales service.
Service |
Specification |
1. Selection |
Send us working data (medium, head, flow rate...) |
2. OEM/ODM |
Please show us the pump design drawing |
3. Process design |
Offer process design as working condition. |
♠♠♠♠♠ CONTACT US ♠♠♠♠♠
Contact AN PUMP about 100 Bar High Pressure Multistage Sea Water Pump
Ailen
Send Inquiry to This Supplier
You May Also Like
-
Spot Danfoss Piston Pump JR-L-S75C-LS-21-25-NN-N3-S1NE-A2NNNN-JJ J-NNNNegotiableMOQ: 1 Piece
-
M, AH, HH Series Slurry PumpNegotiableMOQ: 1 Piece
-
High-Quality Self-Priming Chemical Axial Flow Magnetic Oil Pump for Industrial UseNegotiableMOQ: 10 Bags
-
Water PumpNegotiableMOQ: 2300 Pieces
-
Japan Komatsu PC200-8 PC210-8 PC220-8 Excavator 708-2L-31430 Hydraulic Main Pump 7082L31430US$ 4000 - 5000MOQ: 1 Unit
-
Innovative CMO GHIBLI FOOT PUMP Industrial Solutions for Enhanced PerformanceNegotiableMOQ: 1 Set
-
Manufacturer Direct Selling Fluorine Lined Strong Acid and Alkali Resistant Pump IHF Series Fluorine Plastic Alloy Chemical Centrifugal PumpUS$ 150 - 1600MOQ: 10 Pieces
-
Micro Machining Precision Casting Water Pump Spare PartsUS$ 1 - 30MOQ: 500 Pieces
-
Parts Of Breast PumpUS$ 1,000 - 1,100MOQ: 2 Tons
-
High Quality Oilfield 11kw-50kw Centrifugal PumpNegotiableMOQ: 1 Set
