Contact Platform Support
Help Center4kw Rebar Cutting Machine With 28times/min Frequency
Related Products
-
GQ60 Reinforce Bar Cutter Form China ManufacturerUS$ 700 - 1,000MOQ: 1 Set -
Hot Sale 7.5kw Steel Bar Cutting Machine With Factory PriceUS$ 700 - 1,000MOQ: 1 Set
-
910kg Carbon Steel Rod Cutting Machine in China for SaleUS$ 700 - 1,000MOQ: 1 Set
-
High Quality Construction Steel Bar Bending Machine GW50US$ 1 - 2,000MOQ: 1 Set
-
New Condition China Made High Quality Rebar Bender GW50US$ 1 - 2,000MOQ: 1 Set
wolwa brand steel bar cutter with cluth GQ50
GQ50 Steel Bar Cutter With Clutch
1. GQ50 steel bar cutting adopts enclosed housing, lubricate system, dual-mass flywheel and with clutch structure.
2. It works with high efficiency and safety, which is easy to operate and maintain, light in weight and energy saving.
3. Double mass flywheel, which assure strong enough power for cutting.
Features
1. It is highly structured with reinforced body, small size and reliable quality.
2. It applies the gear splash lubrication system, which is closed case design.
3. If fill enough lubricant oil of 8 or 10kg, it can work continuously for more than three months.
4. Energy saving , because of the improvement of lubrication and the adoption of rolling bearing at the end of gear axis, the resistance is small. Comparing with the other similiar products, our machines can save on third power with the same loading .equipped with rolling wheels, which enables the machine to be moveable .
5. This machine adopts high-rigid knife block and linkage, high-speed machine of national standard. And it has reliable quality and long life.
GQ50 Steel Bar Cutter parameters
Model GQ50 Cutting diameter
Round steel :6-50mm
Class of reinforced steel bar :6-40mm
Flat steel :80*15mm
Angle steel : 63*63mm
Square steel :40*40mm
Cutting frequency : 28times/min
Motor power 4kw
Voltage 380V/50HZ
Dimension 1370*550*880mm N.W: 500KGS
guide graph when steel bar diameter more than 20mm
steel bar diametr(mm) |
6-8 |
9-13 |
14-18 |
19-20 |
20-40 |
steel bar number each time |
6 |
5 |
3 |
2 |
1 |
Matters need attention when using GQ50 Steel Bar
First: The preparing work before use
1, Rotate gears with your hand to ensure the mesh situation is normal.
2, Check the blades is fastness ,the gap between two blades is 0.2-0.5 mm .
3, Check every bolt on the machine.
4, Check electric equipment,ensure the insulativity , equiped electric leakage protection equipment,check the ground electrode connect ground.
5, Must lubricate each rotated part of the machine.
6, No-load test,if there some abnormal phemomenon appear,stop it and repair.
Second:Matters attention when using.
1,Reinforce bar must under the blade ,should not use the top part of blade when there is not necessary ,to prevent overload.
2,When working,the blade must complete,and check the fastness of blade,when it is broken,change a new one right away.
3,If some problem appear when it is working,cut off power source immediately and check repair.
4,Any repair or modify work is forbidden when it is working.
5,Shield must be covered on the machine before running to prevent accident take place.
6,When you tread clutch pedal you must tread it correctly otherwise it will reduce the service life if you usually tread the pedal uncorrectly .
7,When it is cutting, clear the scrap at any time,to prevent the damage of fastness bolt that caused by extrusion.
Maintenance of GQ50 steel bar cutter
1,Clear scrap under blade and near blade with brush.
2,When working,pay attention to the running situation, check the overheating situation of bearing bush.
3,When it work for the first time ,you have to fill gear oil(150-220# gear oil 8 - 10 kilogram in the machine cavity) before, change gear oil one month later.
Vulnerable parts list of GQ50 Steel Bar Cutter
Itme |
Name |
material |
number |
installation site |
1 |
fixed blade |
cutlery steel |
1 |
fastness |
2 |
movable blade |
cutlery steel |
1 |
movable base |
3 |
bearing bush |
powder metallurgy |
1 |
bent shaft right end |
4 |
bearing bush |
powder metallurgy |
1 |
bent shaft left end |
5 |
copper bush |
ZQSn6 |
1 pair |
bent shaft connect rod |
6 |
base plate |
phenolic cloth laminate |
1 |
side shield |
Warm note
In order to prolong service life of the equipment and reduce the cost, please read the instruction manual carefully before operation and maintain the equipment according to signs. Change the OEM gear oil after the first use of 500 hours, then add the same grade gear oil.
Product picture
Our cetificate:
Contact:
Send Inquiry to This Supplier
You May Also Like
-
Best Quality 3kw Cnc Sheet and Tube Fiber Laser Cutting Machine Iron Plate Fiber Laser Cutting Machine PriceNegotiableMOQ: 1 Set
-
FIBER LASER CUTTING MACHINEUS$ 30000 - 31800MOQ: 1 Piece
-
WMT6020D Factory Direct Sale Fiber Laser Cutting Machine With CENegotiableMOQ: 1
-
Laser Cutting Machine for Textile/fabric JQ1630US$ 3,000 - 15,000MOQ: 1 Set
-
China Alibabalaser Cutting Machine Price Low Looking for AgentUS$ 90,000 - 95,000MOQ: 1 Set
-
130x900cm Plywood/Acrylic Laser Engraver Machine PriceNegotiableMOQ: 1 Set
-
Irregular Machine Blade for Steel Sheet PerforatingUS$ 30 - 150MOQ: 1 Piece
-
2 mm Stainless Steel and Mild Steel Laser Cutting Machine for Metal or NonmetalUS$ 8,000 - 13,000MOQ: 1 Set
-
High Precision Sheet Laser CNC Laser Metal Cutting Machine PriceUS$ 18,000 - 60,000MOQ: 1 Set
-
LASER OPTICAL PICK-UP for VAM 2202 15PNegotiableMOQ: 10 Pieces
