Contact Platform Support
Help CenterBiogas Desulfurization,iron Oxide Desulfurizer,natural Gas
Related Products
-
Desulfurization Manufactiring Plant, Natural Gas Iron Oxide DesulfurizerUS$ 450 - 720MOQ: 10 Tons -
Desulfurization Manufacturing Plant, Natural Gas Iron Oxide DesulfurizerUS$ 380 - 720MOQ: 10 Tons
-
Biogas Desulfurization Used in Iron Oxide DesulfurizerUS$ 380 - 720MOQ: 10 Tons
-
Activated Carbon for Sulfur Removal/Desulfurizer for H2s RemovalUS$ 360 - 716MOQ: 10 Tons
-
Ferric Oxide Desulfurizer for Water TreatementUS$ 480 - 680MOQ: 3 Tons
Specifications
1.Gas purification2.Water resistant highstrength
3.High effective
4.Desulfurization effect is good.
Iron oxide desulfurizer for sulfur removal
1. Application
Mainly applicable to the removal of H2S from semi-water gas, water gas, coke oven gas, natural gas, biogas, shift gas in petrochemical and fertilizer production, CO2 regeneration gas, and other gases.
2. Main physical and chemical indicators
Type |
MT-1 |
MT-2 |
Granularity(mm) |
φ(5-6)×(5-15) |
φ(5-6)×(5-15) |
Edgewise compressive strength(N/cm) |
≥40 |
≥50 |
Bulk density(kg/L) |
0.65-0.75 |
0.75-0.85 |
Saturation sulfur capacity (%) |
≥50 |
≥70 |
3. Operation conditions and notes
1),Airspeed: 500-1500h-1
2),Temperature: 10-80°C
3),Pressure: normal pressure
4),Humidity: When remove H2S, humidity is as bigger as better, the best is near to saturated steam, but strictly prohibit to bring water to the bed.
5),Operating: It should be replaced by feed gas before operating, and improve the pressure gradually, then move to the normal production.
6),When regenerate or replace desulfurizer, use inert gas to replace the flammable gas, down to the explosive limit. When regeneration, the air enters form the bottom of the tank, airspeed is 5-50h-1, at the prime of regeneration, the airspeed should be low. The temperature in the tank should be controlled below 110°C, if it is above 110°C, can pause air feeding, when the temperature is below 100°C, then go on. It can finish regeneration when the temperature of the bed is not increase, and the content of O2 in the inlet and outlet is almost the same. When replace desulfurizer, shouldn't exhaust the desulfurizer from the discharge opening in the bottom of the tank, should be exhausted after spraying cooling for safety sake.
Our products' pictures:
Material pictures:
Our packaging and warehouse:
Send Inquiry to This Supplier
You May Also Like
-
Mold Release Agent for Bakery Industry CompliantUS$ 1 - 4MOQ: 200 Kilograms
-
Cyanuric Acid 25kgNegotiableMOQ: 1 Ton
-
Zeolite Carbon Sieves 3a 4a 13x Adsorbent for Oxygen Concentrator Generator Molecular SieveNegotiableMOQ: 1
-
Modified Starch for Paper IndustrialUS$ 630 - 650MOQ: 5 Tons
-
NA Cmc Powder Food GradeUS$ 550 - 3,690MOQ: 5 Tons
-
Diapers Baler Hydraulic Pressing Baling MachineUS$ 3,200 - 3,250MOQ: 1 Set
-
Leather Wall Panel for Background and Ceiling PanelUS$ 3 - 6MOQ: 200 Pieces
-
AC Blowing Foam Blowing Agents of AzodicarbonamideUS$ 2,100 - 2,680MOQ: 1 Ton
-
High Quality Anionic Polyacrylamide Water Treatment Chemicals Polymer /PAM for Waste Water/Oil Drilling/MiningUS$ 1,000 - 2,600MOQ: 1 Metric Ton
-
10-0132 T/r/l Suiting FabricUS$ 2 - 3MOQ: 3000 Meters
