Breast Lifting Up Permanent Hair Removal At Home Review Salon Ipl Hair Removal Laser Portable Electrolysis Hair Removal Machine 2.6MHZ

permanent electrolysis hair removal machine:

Applications of electrolysis hair removal machine:

Technical parameter of electrolysis hair removal machine:

Hair removal of electrolysis hair removal machine:

1. Cut or shave hair to 1-2mm or ask patients to shave at home 2-3 days before treatment.

2. Clear treatment area.

3. Turn on machine,

1). Use SHR, adjust pulse width at 7ms, frequency 5HZ, energy 10J/cm2.

2). Use normal hair removal treatment, put the 640nm or 690nm filter into the slot, select

"hair removal",adjust the parameter, set it to ‘ready’ .

4. Put cooling gel on treatment area about 2mm.

5. Wear protect goggles for patient and operator.

6. Shot the treatment area, let the crystal tip to touch cooling gel, You are permitted to have

1/3 overlapping on treatment area.

7. Wipe off cooling gel after treatment and clear treatment area with cooling water. If patients

   feel warm or hot, you may put ice bag on treatment area until heat disappear.

Skin rejuvenation:

Product Introduction

Precipulse IPL Therapy System holds a wavelength from 420nm to 1200nm.Different wavelength is adopted in treatment based on clinical requirements.This system is focus on treating various kinds of clinical indications including pigmented lesions and vascular diseased as well as hair removal and skin rejuvenation.It contains a wide clinical application range.

1. Clear treatment area.

2. Turn on machine ,put the 560nm filter into the slot, select "skin rejuvenation",adjust the

parameter, set it to ‘ready’ .

3. Put cooling gel on treatment area about 2mm, you are suggested to put cooling gel in refrigerator to keep temperature of gel during 0-4°C.

4. Wear goggles for patient and operator

5. Shot the treatment area, let the crystal tip to touch cooling gel. You are permitted to have

1/3 overlapping on treatment area.

6. Wipe off cooling gel after treatment and clear treatment area with cooling water. If patients

   feel warm or hot, you may put ice bag on treatment area for 30 minutes until heat-feeling

   disappears.

Pigmentation Therapy:

1. Clear treatment area.

2. Turn on machine ,put the 480nm or 530nm filter into the slot, select "pigmentation

therapy",adjust the parameter, set it to ‘ready’ .

3. Put cooling gel on treatment area about 2mm, you are suggested to put cooling gel in

   refrigerator to keep temperature of gel during 0-4°C.

4. Wear goggles for patient and operator

5. Shot the treatment area, let the crystal tip to touch cooling gel. You are permitted to have

1/3 overlapping on treatment area.

6. Wipe off cooling gel after treatment and clear treatment area with cooling water. If patients

feel warm or hot, you may put ice bag on treatment area for 30 minutes until heat-feeling

disappears.

Vascular Therapy:

1. Clear treatment area.

2. Turn on machine ,put the 580nm filter into the slot, select "vascular therapy",adjust the

   parameter, set it to ‘ready’ .

3. Put cooling gel on treatment area about 2mm, you are suggested to put cooling gel in

   refrigerator to keep temperature of gel during 0-4°C.

4. Wear goggles for patient and operator

5. Shot the treatment area, let the crystal tip to touch cooling gel. You are permitted to have

1/3 overlapping on treatment area.

6. Wipe off cooling gel after treatment and clear treatment area with cooling water. If patients

feel warm or hot, you may put ice bag on treatment area for 30 minutes until heat-feeling

disappears.

Acne Therapy:

1. Clear treatment area.

2. Turn on machine ,put the 430nm filter into the slot, select "acne therapy",adjust the

parameter, set it to ‘ready’ .

3. Put cooling gel on treatment area about 2mm, you are suggested to put cooling gel in

refrigerator to keep temperature of gel during 0-4°C.

4. Wear goggles for patient and operator

5. Shot the treatment area, let the crystal tip to touch cooling gel. You are permitted to have

1/3 overlapping on treatment area.

6. Wipe off cooling gel after treatment and clear treatment area with cooling water. If patients

feel warm or hot, you may put ice bag on treatment area for 30 minutes until heat-feeling

disappears.

Wrinkle removal:

1. Clear treatment area.

2. Turn on machine ,put the 580nm filter into the slot, select "wrinkle removal",adjust the

parameter, set it to ‘ready’ .

3. Put cooling gel on treatment area about 2mm, you are suggested to put cooling gel in

refrigerator to keep temperature of gel during 0-4°C.

4. Wear goggles for patient and operator

5. Shot the treatment area, let the crystal tip to touch cooling gel. You are permitted to have

1/3 overlapping on treatment area.

6. Wipe off cooling gel after treatment and clear treatment area with cooling water. If patients

feel warm or hot, you may put ice bag on treatment area for 30 minutes until heat-feeling

disappears.