EU 24 Volt 0.75 Amps 18 Watts Wall plug type AC/DC Power Adapter

Features 

• Universal AC input: 100~240Vac 
• Protections: Short circuit / Overload 
• No load power consumption < 0.5W /Over voltage 
• 2 or 3 pole US / European type plug 
• Fully enclosed plastic case
• Class II power (without earth pin)
• Full output 12v,24v, safety approved 
• 18 months warranty

General Specification

• AC input voltage range ............. 100~240VAC / 0.75A for18W
• AC inrush current (max.) ........... Cold start, <30A peak at 115VAC or <50A peak at 230VAC
• Overload protection...................  Hiccup mode, auto-recovery
• Over voltage protection ............. Clamp by zener diode > 120%
• Withstand voltage......................  I/P-O/P: 4242VDC, 1minute
• Working temperature.................. 0~40°C @ 100% load, 50°C @ 70% load
• Safety standards........................  EN61347-1-2, UL60950-1, CSA 22.2, TUV EN60950-1
• EMC standards..........................  EN55022-B, EN61000-3-2,3, EN61000-4-2,3,4,5,6,11
• Length of output cable................ 180cm of UL1185, 20AWG
• Standard DC plug.......................  P1J: 5.5øx2.1øx10mm  /  -C+, turning fork type

EFFICIENCY:

   When 230VAC line input voltage (100-240 VAC),the efficiency shall be >79% at rating load.

DIELECTRIC STRENGTH (Hi-Pot) TEST:

   Finished product withstands with AC 3000Vrms/50Hz,5mA max,

   primary to secondary, 1 minute for type test,1 second for production test.

INSULATION RESISTANCE:

   Primary to secondary: 10MΩ min at 500VDC. 

PROTECTION:

Short Circuit Protection

   If short circuit occurs,all the output should be protected. After the fault, the adapter automatically recovers.

Over Shoot

    The Output over shoot at turn-on shall not exceed 10% of normal voltage value with or without the load connected.

Start-up time

    The start-up time is less than 2 second.

ENVIRONMENTAL CONDITIONS:

Temperature

    Operating temperature:  0℃  to  +40℃

    Storage temperature :  -20℃ to  +60℃

Humidity

Relative humidity:≤95%

Operating Ambient Altitude

     Altitude:0-3000m

Operating at the lower temperature

      At -0℃,with the rated voltage 100-240Vac charged to the primary and unloaded and full load on the secondary 8 hours, no abnormality in electric and mechanical characteristic, after 2 hours recovery  at the room  temperature.

Operating at the high temperature

      At +40℃,with the rated voltage 100-240Vac charged to the primary and unloaded and full Load on the secondary 8 hours, no abnormality in electric and mechanical characteristic, after 2 hours recovery  at the room  temperature.

COOLING:

      Cooling shall be with natural convection cooling.

Burn-in

    The burn-in test will be performed at least 4 hours at centigrade

    degrees under full load Condition.

Referenced standard:

EMI Standards

    Reference  EN50082-1,EN55022-B,GB-17625.1-2003, GB-9254-1998

Safety Standards

    The adapter shall be meet certified with the following safety standards.

    UL60950-1,EN60950-1,GB4943-2001

MOUNTING CONNECTORS:

AC Input Connector

     Spec :2Pin  (CE  PIN)

DC Output Cable

      Wire : (Optional)  24AWG*2C  L=1200mm Color: Black

     Plug : (Optional) 5.5 x 2.1x 10mm  Turning fork line

MECHANICAL FEATURES:

Dimension(Size)

     Length: 59.8mm

     Width: 38.8mm

     Height: 45mm

Weight

     The Power Supply unit : 65±10g

Vibration and shock

      No Evidence of any mechanical or functional damage after the vibration and shock testing.

Drop test

After Dropping from a hight  of   100  cm onto a wooden floor , Dropping at  6  sides  totally,  NO breakage should be happened in the test piece.

Bending Test

     Fix the power supply and its plug, apply a load of 200g to the other end, turn the cable by +/-60℃ carry out this process 1000 times, at the rate of 20 times per minutes. No abnormality in mechanical and electrical Characteristic and disconnection within 30% after the test.

What's the other type power supply do you have???                                                                                   

Answer: We specialized in constant voltage & current LED drivers, 010v/triac/DALI dimmable led drivers, enclosure power suppliers, power adapters.

Why choose Quanzhou Smarts Electronic & Technology Co.,Ltd ???                                                     

1).  Our major markets are in EU & North America,it takes about 85% markets share,that to say we do high quanlity power suppliers only.

2).  Most of our products are approved with UL/CE/Rohs approval, our ULfile#E365202.

3).  We give 2 years warranty

4).  We accept trial orders begining.. 

5). We  have an area of 2000 square meters factory,  about 300-500 production staff. ..

Website:   

our team:                                                                                                                                                                                                               

certifications:                                                                                                                                                                                                              

CE, UL/CUL, ROHS approval.

our market                                                                                                                                                                                                                    

Our major markets are in EU & North America,it takes about 70% markets share. view  transaction history

factory & equipments view:                                                                                                                                                                         

what is the packing situation for ??                                                                                                                                                                                                                                                                             

Answer: inner box-white box + outer carton- standard exporting carton for packing.

• Inner box: white box 
• Outer carton:  standard exporting carton for packing

Shipping:                                                                                                                                                                                                       

• Samples: FedEx, DHL, UPS or TNT ;
• Batch Goods: By Air or By Sea  for FCL;
• Customers Specifying Freight Forwarders or Negotiable Shipping Methods;

Our service & FAQ                                                                                                                                     

Q1.    What's the trade terms you can do??
A1:    We accept EXW,FOB..(Optional)
 
Q2.    What's shipping mode can we choose?
A2:    Express, Ocean and air transportation (optional).
 
Q3.    What's the MOQ?
A3:    Our MOQ is 10pcs. better price for large quantity;
 
Q4.    What can you do if the product is broken?
A4:    We promise to replace new ones to you if there is any defective happen during the warranty period.
 
Q5.    Can i get products with my own logo?? 
A5:    Sure, you can, MOQ is 500pcs.

Q6.    Can i get a sample for testing?? 
A6:    Sure, but sample fees should be charged on your account.
 
Q7.    What's the mormal lead time??
A7:    7 working days for samples, 15 working days for mass production.
 
Q8.    What's the payment conditon?
A8:    All are paid before production or 30% deposit and 70% before delivery (optional)
 
Q9.    What's the Payment do you have?
A9:    We accept payment be sent via T/T, L/C,  Trade Assurance, WESTERN UNION, PAYPAL.

Send your inquiry details in the bellow for professional reply,
click "    send   " now !