HDMI Matrix 4x4 with Simultaneous CAT and HDMI Outputs

INTRODUCTION

The 4x4 HDMI Matrix with simultaneous CAT and HDMI outputs connects four HDMI sources to eight displays. This matrix features four HDMI outputs and each HDMI output is mirrored to provide a CAT-Cable output which runs simultaneously. Connect a SINGEL UTP Receiver to each of the CAT-Cable outputs to extend the HDMI signal up to 164ft/50m for multi-room connectivity. It works with Blu-Ray players, Set-Top boxes, Home Theater PCs, and game consoles that connect to an HDMI display. Any source is accessible at all times by any display by selecting it via the supplied IR Remote Control, RS-232, TCP/IP or by using the selection buttons on the front panel. This device supports High Definition Audio, and 3D signal compatibility.

Feature

l         HDMI1.3, HDCP 1.1 and DVI1.0 compliant.

l         Supports HDMI 3D pass-through.

l         Supports resolutions from VGA~WUXGA and HD resolutions from 480i~1080p dependent upon the EDID settings.

l         Supports transmission distances up to 164ft/50m through CAT5e/6/7 cable.

l         Supports simultaneous HDMI and CAT outputs.

l         Supports wideband IR(20-60Khz) matrix system, IR transport channel can be forward or backward.

l         Supports RS-232, remote control, on-panel control and TCP/IP Control.

l         Supports smart EDID management.

l         Supports LPCM 7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio transmission.

SPECIFICATIONS

1. Video Bandwidth                     165 MHz
2. Support Video Resolution        480i,576i,480p,576p,720p,1080i,1080p24/30/50/60.
3. Input Ports                               4×HDMI, 4×IR Extender, 1×RS-232, 1xRJ-45(Control),1xMatrix IR Extender
4. Output Ports                            4×CAT, 4×IR Extender, 4×HDMI
5. ESD Protection                         Human-body Model:  ± 8kV (Air-gap discharge), ± 4kV (Contact discharge)
6. Power Supply                           12 V/2.5 A DC (US/EU standards,CE/FCC/UL certified)
7. Dimensions                              440 mm (W)×200 mm (D)×45 mm (H)
8. Weight                                     1820 g
9. Chassis Material                      Metal
10. Silkscreen Color                       Black
11. Operating Temperature           0 ºC~40 ºC/32 ºF~104 ºF
12. Storage Temperature               −20 ºC~60 ºC/−4 ºF~140 ºF
13. Relative Humidity                   20~90 % RH (non-condensing)
14. Power Consumption                23 W(max)/0.5w(Standby)

PANEL FUNCTIONS

Front Panel

1.      PC CONTROL

TCP/IP: This port is the link for TCP/IP controls, connect to an active Ethernet link with an RJ45 terminated cable.

RS232: Connect to a PC or control system with D-Sub 9-pin cable for the transmission of RS-232 commands.  

 

2.      IR Channel

IR EXT: if the panel sensor is obstructed or the unit is installed in a closed area out of infrared line of sight, the IR RX receiver included can be inserted into the IR EXT port at the rear to extend the IR sensor range and enable local control of the matrix.

IR IN/OUT: Super IR control system interface. for further details, please refer to the Super IR system control introduction.

 

3.      HDMI INPUT

Connect to the HDMI input source devices such as a DVD player or a Set-top Box with HDMI cable.

 

4.      HDMI and CAT OUTPUT

The HDMI OUTPUT connect to HDMI equipped TVs or monitors and the CAT OUTPUT connect to the SINGEL UTP Receiver.

 

5.      DC POWER IN

Plug the 12V/2.5A DC power supply into the unit and connect the adaptor to an AC outlet.

 

 

Remote Control

 

 

 1. Press this button to power on the matrix or set it to standby mode.

 

2.Press these button to select output A,B,C,D for input 1,2,3,4 port.

 

Operate and Connect