Contact Platform Support
Help CenterQCX601 RINGing SLIC RSLIC Signal Generator for VoIP Cable Modems
Related Products
-
Ring Slic QCX601 With Tip/Ring Polarity Reversal On-hook Transmission Off-hook DetectionUS$ 1 - 4MOQ: 1 Unit -
QCX601 Low Power Ringing SLIC MODULE for Use Short Loop "on-premise" Applications,such as FCT,FWT, WLL and VoIPUS$ 1 - 4MOQ: 1 Unit
-
Low Power Ringing SLIC Module QCX601 for Short Loop Access PlatformsUS$ 1 - 4MOQ: 1 Unit
-
QCX601 Low Power Ringing SLIC MODULE'US$ 1 - 4MOQ: 1 Unit
-
+3.3V to +5.0V Low Power Ringing SLIC for IP Gateway SystemUS$ 1 - 4MOQ: 1 Unit
Specifications
Low Power Ringing SLIC MODULE QCX601have the DC/DC converter
Cable Modems
Voice Over DSL(VoDSL)
Low Power Ringing SLIC MODULE QCX601
The QCX601 is designed for use short loop “on-premise” applications, such as FCT, FWT, WLL and
VoIP. In this case power cross and lightning protection is not required. The only protection which
should be required is for ESD (Electro Static Discharge) caused by handling during installation.
1. Features
Single supply voltage: +3.3V to +5.0V.
Integral high efficiency DC/DC converter.
Transformerless 2-wire to 4-wire conversion
Integral ringing generator
Constant current feed
Tip/Ring Polarity reversal
On-hook transmission
Off-hook detection
Easy to use, with a minimum number of external components.
Simplified protection in “on-premise” applications.
2. Applications
Voice Over Internet Protocol (VoIP)
Cable Modems
Key Telephone System
IP Gateway system
Wireless Desktop Phone
Set-top Box System
Voice Over DSL (VoDSL)
Short Loop Access Platforms
Remote Subscriber Units
Other Terminal Adapters
3. Product Selector
4.Functional Description
1).Switch Hook Detection
When the subscriber goes “off-hook” loop current will begin to flow. If this current is above the detection threshold the switch hook output, SHK, will switch to a logic (H). It is recommended that software or hardware de-bouncing of the switch hook signal is used. This is to avoid short pulses which can cause a false switch hook output, triggering the incorrect system response.
During loop disconnect dialling, SHK will pulse between logic (H) and logic (L) to indicate the digits being dialled. Again it is recommended that software de-bouncing of the pulse edges is used to avoid false detection of digits
2). Tip & Ring Polarity
The QCX601 can reverse the battery voltage polarity at Tip and Ring via the RFL pin. RC and 25HZ is at logic (L):
If RFL is held at logic (H) (Forward) the d.c. voltage at Ring is negative with respect to Tip. If RFL is taken to logic (L) (Reverse) the voltage at Ring is positive with respect to Tip.
The QCX601 is designed for use short loop “on-premise” applications, such as FCT, FWT, WLL and VoIP. In this case power cross and lightning protection is not required. The only protection which should be required is for ESD (Electro Static Discharge) caused by handling during installation.
3) Ringing Signal Waveforms
Send Inquiry to This Supplier
You May Also Like
-
Heavy-Duty DC Combiner Box With Circuit Breakers, Fuses, and 5-Year WarrantyUS$ 30 - 50MOQ: 30 Units
-
Electronic CapacitorNegotiableMOQ: 2000 Pieces
-
6\"/8\" FramesNegotiableMOQ: 500 Pieces
-
Turing F1280 High-Resolution IR Module: Precise Thermal Perception for Continuous OperationNegotiableMOQ: 50 Pieces
-
Oven Capacitor CH85 2100VAC Capacitor for MicrowaveNegotiableMOQ: 1
-
20kA Surge Protective Device SPD (SP-D10)US$ 0.01 - 0.02MOQ: 1 Piece
-
IRFP450,100% New and Original. Top Sales!!!NegotiableMOQ: 100 Pieces
-
Miniature Capacitor 2.7v1f 6.3x9mm Super CapacitorUS$ 0.35 - 0.5MOQ: 100 Pieces
-
50V 10UF CapacitorUS$ 0.5 - 1MOQ: 200 Pieces
-
BNCHG Terminal Block Pin Connector for Over 12 Year ExperienceUS$ 0.35 - 0.4MOQ: 10000 Sets
