Contact Platform Support
Help Center(N-TYPE) MADE IN TAIWAN VARNISH COATING BRANDS POLYURETHANE VARNISH
Related Products
-
(N-TYPE) MADE IN TAIWAN ANTI WEAR COATING METAL VARNISH CLEAR VARNISH FOR METALUS$ 20.54 - 25.6MOQ: 360 Sets -
MADE IN TAIWAN COLOR COATING LIFE PAINT SPRAY BLUE PAINTUS$ 50 - 62.5MOQ: 120 Barrels
-
(N-TYPE)HIGH FRICTION PAINT COATING ACRYLIC URETHANE LIQUID METAL SPRAY PAINTUS$ 21.6 - 26.2MOQ: 360 Sets
-
(SOLVENT-LESS) MADE IN TAIWAN OIL RESISTANT SELF-LEVELING CAR PARK FLOOR PAINTUS$ 77.9 - 88.9MOQ: 120 Sets
-
(SOLVENT-LESS) MADE IN TAIWAN GARAGE 3D EPOXY FLOOR COATING SCREEDING PAINTUS$ 77.9 - 88.9MOQ: 120 Sets
(N-TYPE) MADE IN TAIWAN VARNISH COATING BRANDS POLYURETHANE VARNISH
POLYURETHANE CLEAR COATING (N-TYPE) | |
TYPE |
A two-pack, non-yellowing clear paint based on acrylic resin, polyol resin polymer and polyisocyanate hardener. |
USES |
Clear topcoat for metalware and woodenware such as furniture, musical instruments, handicrafts, sports equipment etc. |
CHARACTERISTICS |
1. High gloss and hardness, good gloss and color retention. 2. Excellent adhesion for wooden and metal wares. 3. Excellent abrasive and heat resistance. |
GLOSS |
Above 90% |
APPEARANCE |
Clear liquid |
WEIGHT |
Above 1.0 kg/L (Mixer) |
VISCOSITY (25 ℃) |
55~80 KU ( mixture, 25℃ ) |
OPTIMUM FILM THICKNESS |
Wet 50 microns Dry 25 microns |
MIXER RATIO |
Base : hardener = 2 : 1 (by volume) |
DRYING TIME (25 ℃) |
Set-to-touch 2 hr. Dry hard 8 hrs. (25 ℃). |
NON-VOLATILE CONTENT |
Above 50% ( mixture ) |
POT LIFE |
4 hrs. ( mixture, 25℃ ) |
THINNER |
PU thinner |
THINNING RATE |
5~20 % |
STORAGE SHELF LIFE |
Minimum 1 year under normal storage conditions. |
APPLICATION METHOD |
Spray, Brush |
NOTE |
1. Mix base and hardener according to the mixing ratio and stir thoroughly. 2. Adhered moisture, grease, and dirt on substrate must be cleaned thoroughly. 3. Use specified thinner to avoid formation of bubbles and pinholes. 4. The lid of hardener barrel must be tightly closed to prevent the contact with moisture in the air to avoid generating bubbles and gel. 5. The mixture must be available within the pot life. 6. The sprayed thickness of paint film exceeded 50microns per coat that is easy to generate bubbles. It must be done effective control when applied. 7. All equipment must be thoroughly cleaned immediately after use to avoid gel. 8. The brushing type can also be applied by roller, but to roll the polyurethane or fluorocarbon paints, the film thickness is easy too thick to generate small bubbles. It shall pay special attention to. |
Send Inquiry to This Supplier
You May Also Like
-
Anti-static Self-leveling Epoxy Floor CoatingNegotiableMOQ: 1
-
Polyethylene LDPE Powder Coating for Automotive Parts With UV StabilityUS$ 2 - 5MOQ: 1000 Kilograms
-
Building CoatingNegotiableMOQ: 2700 Kilograms
-
Titanium Dioxide Rutile Type 93% Used for Paint STD001 Shijiazhuang Standard ChemicalsUS$ 100 - 2000MOQ: 1 Ton
-
Aliphatic Polyurethane Paint for BuildingUS$ 1.8 - 8MOQ: 1000 Kilograms
-
Rotary Water Spray RoomNegotiableMOQ: 1 Set
-
EASY PAINTNegotiableMOQ: 2000 Pieces
-
Rubber Paint on SaleUS$ 1.45 - 35.21MOQ: 100 Pieces
-
Powder Coating EquipmentUS$ 75,000 - 950,000MOQ: 1 Set
-
Glass Car Body Coating From JapanUS$ 150,000 - 150,000MOQ: 1 Carton
