Contact Platform Support
Help CenterLow Noise Inertia Measurement Unit Low Bias Instability
Related Products
-
Tactical Grade Inertial Measurement Unit STIM300 IMU Factory CalibratedNegotiableMOQ: 1 Piece -
Low Cost MEMS Six Axis Sensor IMU Measure Angle Rate and AccelerationUS$ 1 - 700MOQ: 1 Piece
-
High Performance MEMS Inertial Measure Unit MEMS IMU Best Price Quality ChoiceUS$ 1,000 - 1,000MOQ: 1 Piece
-
Gradient Meter, Gradiometer,inclinometer SensorNegotiableMOQ: 1 Piece
-
Factory Supply Digital Compass RS232 Easy CalibrationNegotiableMOQ: 1 Piece
Low noise Inertia Measurement Unit Low bias instability
STIM300 is an IMU consisting of 3 high accuracy MEMS-based gyros, 3 high stability accelerometers and 3 high stability inclinometers in a miniature package. Each axis is factory-calibrated for bias,sensitivity and compensated for temperature effects to provide high accuracy measurements in the temperature range -40°C to +85°C. The unit runs off a single +5V supply.STIM300 communicates via a standard high level RS422 interface. The use of a 32-bit RISC ARM microcontroller provides flexibility in the configuration, like choice of output unit, sample rate,low pass filter -3dB frequency and RS422 bit-rate and protocol parameters. All configurable parameters can be defined when ordering or set by customer.When STIM300 is powered up, it will perform an internal system check and synchronise the sensor channels. As an acknowledgement of the complete power-up sequence, it will provide special datagrams containing part number, serial number and configuration data. STIM300 will then automatically proceed to provide measurement data. Connect power and STIM300 will provide accurate measurements over the RS422 interface.The measurement data is transmitted as packages of data on a fixed format (datagram) at intervals given by the sample rate together with a synchronization signal (TOV). The datagram is in binary coded format in order to have an efficient transfer of data. In ddition to the measurement data itself, the datagram contains an identifier, status bytes and a 32 bit CRC (Cyclic Redundancy Check) to provide high degree of fault detection in the transmissions. The status bytes will flag any detected errors in the system. STIM300 can also be configured to transmit data only when triggered by a separate digital input signal (ExtTrig).For more advanced users, the gyro may be put in Service Mode. In this mode all the configuration parameters can be intermediately or permanently changed by overwriting the current settings in the flash memory. In Service Mode the commands and responses are in a human readable format (ASCII); to enable the use of terminal-type software during typical product integration. Service Mode also provides the ability to perform single measurements, perform diagnostics and obtain a higher detail level of detected errors reported in the status bytes.
Product Show:
- Packaging: carton with sponge
- Delivery time: within 7 business days for common order after we receive the full payment
-
Shipping time: 3-5 work days by DHL/UPS/FEDEX/TNT; 5-7 work days by EMS.Our Services
Pre-sale service
- Evaluate your application, recommend the most suitable item;
- Make you fully understand the products, usage and maitenance;
- Answer all your questions, and let you have no doubt before make any decision;
- Adjust, revise or redesign our products to consist with the application(for customized service);
Sales service
- Recommend the best payment term and shipping term for you;
- Make official quotation and PI with company Stamp;
- Keep you posted about the products producing;
- Send exactly requried products on time;
- Provide tracking NO. and inform you when products leave factory and arrive destination;
Post-sale service
- Instruct products connection, installation and application;
- if anything happen to products(barely will), engineer will evaluate the problem, solve the problem or exchange malfunction item for free, make sure you get the best solution and service.
- Keep tracking the products usage and ask for suggestion and advice.
Shenzhen RION, as a positon sensor manufacturer and solution expert, attaches much importance to products reseach and develop which spend over 20% of annual profit. We have the most R&D personnel and best technology comparing with our peer to raise our up on the high level of sensor field. And we orientate ourself to market tightly and engage ourself into providing the most considerate and professional solution and service to customers. RION introduce advanced equipment, such as TEMP&HUMI chamber, salt spray corrosion test chamber, high precision automatic turntable, high precision marble checking platform, digital thermostat drying oven, electrostatic discharge tester and 360 degree mechanical turntable etc, and set up Environmental Testing Laboratory, Product Aging Chamber, 2D&3D Posture Calibration Room and Shake&Impact Test Room for R&D and factory test.
Beside owning excellent hardware, RION also developed 15 sets of software independently and keep developing, including multi-sensor monitor software, remote sensor monitor software, synchronous dynamic l tracking 3D presentation software, tilt switch early warning and debugging software and sensor serial port setting presentation software etc which could apply to XP, Win7, Win8, WinCE and Android system. RION, owning talent and diligent personnel, advanced technology and market-orientated strategy, engages itself in offerring you the most considerate and professional solution and service of position sensor.
You satisfaction is our mission.
Certificates & Honor
-
FAQ
- How to choose suitable item: bowse our webiste and choose products by catalog, or contact us directly by email, skype, TM.
- How to buy: We accept the payment by Escrow/Alipay,including Paypal,Credit Card and T/T, WU.
- How to ship: by DHL, Fedex, UPS, EMS, TNT and ARAMEX Express mainly, we have long term and reliable logistic cooperator to ensure the safety and cost-saving
- How to apply: We provide instruction manual, software and online service to instuct you to connect, install, use and maintain our products.
- What if anything happen to products: contact us, we will evaluate the problem and instruct you, exchange the wrongly purchased item or fix the malfunction item for free...till you get the best solution.
- What if no suitable item to be found: customerized service is available.
- How to cooperate: we offer technical support, products info, samples, favorable terms&condition and sales support in concerned region.
Send Inquiry to This Supplier
You May Also Like
-
3D MEMS Gyro Compass for Underground NavigationNegotiableMOQ: 1 Piece
-
Factory Supply Dual Axis High Precision Inclinometers Level SensorsNegotiableMOQ: 1 Piece
-
Anti-interference MEMS Gyroscope High PerformanceUS$ 1 - 700MOQ: 1 Piece
-
High Accuracy Inclination Alarm Sensor Slope AlarmerNegotiableMOQ: 1 Piece
-
Powerful Synergistic Guidance Navigation & Control IMU Vibration and EMI ResistanceNegotiableMOQ: 1 Piece
-
Tightly Integrated GNSS/INS Navigation System IMU Inertial Measurement Unit Low CostNegotiableMOQ: 1 Piece
-
Factory Price Cheap Compass Module 2D CalibrationNegotiableMOQ: 1 Piece
-
Cheap Analog Tilt Sensor 0.01 ResolutionNegotiableMOQ: 1 Piece
-
AH106B High Accuracy Six Free Degree Inertial Measurement Unit Consist of 3 Axis MEMS Gyro 3 Axis MEMS AccelerometerNegotiableMOQ: 1 Piece
-
AH100B Super Precision Digital Position Indicator High Performance Position Sensor for Fast Moving ObjectNegotiableMOQ: 1 Piece
