Home > Products > Z-wave Sensors > Z-wave Three Beams active Infrared sensor
Z-wave Three Beams active Infrared sensor
- 1000 Piece / Pieces per Month
- Shenzhen
- T/T L/C D/P D/A Credit Card PayPal
Product Details
Place of Origin: | Guangdong, China | Brand Name: | EVA LOGIK | Model Number: | ZW113B |
Usage: | Position Sensor | Theory: | Optical Sensor | Output: | Digital Sensor |
Product Description
Introduction
This sensor is a Z-Wave enabled device (interoperable, two-way RF mesh networking technology) and is fully compatible with any Z-Wave enabled network.
Technical data
*Detection range: 30~100meter;
*Detection angle: 180°±90°(horizontal); 20°±10°(vertical)
*Power supply: 12VDC
*Range: 30m line of sight
*Operating temp: -25°--+55°(℃)
*Quiescent current: 18(uA)
*Alarm current: 100(uA)
*Dimensions: 171(L)*50(W)*77(H)mm
*Frequency: 868.42MHz/865.2MHz/869.0MHz/908.42MHz/921.42MHz
Installation
1. Release cover tab to open the cover.
2. Install ZW113 to the relate position, avoid obstacles such as trees, insure the set-base is stable, and avoid sunshine/lamplight directly shining.
3. Close the cover back to sensor.
4. For “Add” in (adding to): Put the Z-Wave Interface Controller into “Add” mode, and following its instruction to add the ZW113 to your controller. To get in the “Add” mode, the distance between sensor and controller is suggested to be in one meter. Press the learn switch of ZW113 once. The LED on the ZW113 should stop flashing, if not, please try again. For “Remove” from (removing from) a network: Put the Z-Wave Interface Controller into “Remove” mode, and following its instruction to delete the ZW113 to your controller. Press the learn switch of ZW113 once to be excluded. The LED on the ZW113 should start to flash. For “Group”: removing the cover of the ZW113 to get into “Awake” mode, then put the Z-Wave Interface Controller into “Group”, and following its instruction to associate the ZW113 with other device. Close the cover back after “Group” done, afterward the ZW113 will get into “Sleep” mode for power saving. Support one association group (5 nodes). Note: ”Awake” mode: it is to leave the “Sleep” mode by removing the cover of ZW113, to allow the Z-Wave Interface Controller to do “Group.
5. Using gum wall plug & screws to mount ZW113 at 2 meters above surface. To enhance proper operation, place ZW113 on the angle which can detect the room widely. The solid area means the detector’s coverage range.
Safety and maintenance instruction
- Make sure that all electric connections and connection cables meet the pertaining regulations and are in conformity with the operating instruction.
- Do not overload electrical outlets or extension cords, fire or electric shocks can be the result.
- Please contact an expert in case you have any doubts about the mode of operation, the safety or connecting the appliances.
- Keep all parts away from young children’s reach.
- Do not store this item on wet, very cold or warm places, this can damage the electronic circuit boards.
- Avoid dropping or shocks, this can damage the electronic boards.
- Never replace damaged power cables yourself! In such case, remove them from the net and take the devices to a workshop.
- Wireless system are subject to interference from cordless phones, microwaves, and other wireless devices during installation and operation.
Maintenance
The devices are maintenance-free, so never open them. The guarantee becomes void when you open the appliance. Only clean the outside of the devices with a soft, dry cloth or a brush. Prior to cleaning, remove the devices from all voltage sources.
NOTE
Do not use any carboxylic cleaning agents or petrol, alcohol or similar. These will attack the surface of devices. Besides, the vapors are hazardous to your health and explosive. Do not use any sharp edged tools, screw drivers, metal brushes or similar for cleaning.
Warranty 1 year
Contact Us
- Dongguan NIE Technology Co., Ltd.
- Contact nameWinnie Wen
- Phone0086-769-33379207
- AddressThird Floor, Building B, Licheng Industry City, Zhendi Village, Xinan Community, Changan Town
- TURCK-6625035 RSC4T-5/ RSC4T5 TURCK-6625036 RSC4T-10/ RSC4T10
- TURCK-6618613 RSAV-RSAV-849A-6M RSAVRSAV849A6M
- TURCK-6611975 TB-4M12-4-20/TXL TB4M12420 TXL
- TURCK-6611824 RKV493O-15M RKV493O15M
- TURCK-6611743 WFKD8-PCBH WFKD8PCBH
- TURCK-6611494 JBBS-49SC-T614/3G JBBS49SCT614 3G
- TURCK-6611305 CABLE-LWL-2ST/SY-100M CABLELWL2ST SY100M
- TURCK-6611305 CABLE-LWL-2ST/SY-100M CABLELWL2ST SY100M
- TURCK-6611264 RSC-WKC5723-2M RSCWKC57232M
- Turck NI65R-S32SR-AP44X-S1131 Nr:1440009
- Turck BI15-M30-AP6X Nr:4618530
- TURCK-6611229 RKCV483B-6M RKCV483B6M TURCK-6611230 RKCV483B-8M
- China supplier LVDT Position Sensor TDZ-1E-11 power plant spare parts
- China supplier SWITCH PRESSURE BH-209028-209 power plant spare parts
- China manufacturer Turbin Expansion Sensor TD-2-25 for power generation
- China factory LVDT Sensor TDZ-1E-03 for power station
- China factory Heater for low woltage switchgears DRJ100 100W for power station
- TURCK flow sensor flow meter 3079108 K50LGXRPQP 3075671 K50LGRYPQ
- TURCK flow sensor flow meter 3079108 K50LGXRPQP 3075671 K50LGRYPQ
- TURCK flow sensor flow meter 3074907 K50APFF100GXDQP
- Small Size Fiber Optic Gyroscope
- High-sensitive Multifunction power meter PD194E-9F2 for Thermal power material
- Intelligent LVDT sensor DEA-LVDT-100-6 for India power system
- Wearable Expanda Cable Coil for soot blower IK-530 Quality assurance
Popular Searches
Recommended Products
- 3240 Epoxy Board, High-quality Insulation Material, Flexible Customization, Widely Applicable 3240 Epoxy Sheet
- Chinese Factory Electrical Insulation Brown 3025 Phenolic Bakelite Resin Cotton Cloth Fabric Laminate Board Sheet Phenolic Board
- 4x8 fiberglass sheets g10 epoxy glass fiber board g10 material
- Factory Price Bakelite Decorative HPL Press plates bakelite sheet
- Black G10 Sheet - High Quality Carbon Fiber G10 FR4 Sheets - Precision-made PCB Materials
- 3025 Micarta Linen Phenolic Cotton Canvas Bakelite Sheet
- Electrical insulation Epoxy Resin fiber glass tube g10 g11 fr4 epoxy fiberglass tube
- Factory hot sale laminate fr4 g10 good Quality Black High 4x8 Fiberglass Sheets plate with BOM/One-stop service
- G10 Fiberglass Sheet Knife Handle Materials 6mm g10 knife handle material
- VCXO 32.768Mhz ±50ppm 1.8V SMD Voltage Controlled Crystal Oscillator VTKUPLSANF-32.768000
- VCXO 200Mhz ±50ppm 3.3V SMD Voltage Controlled Crystal Oscillator VTEMPCJANF-200.000000
- VCXO 61.44Mhz ±50ppm 3.3V SMD Voltage Controlled Crystal Oscillator VTEUPLJANF-61.440000
Find Similar Products By Category
- Electronic Components & Supplies > Active Components > Sensors
- Buy on GoldSupplier.com
- How to Buy
- Browse by Catagories
- Browse by Hot Regoins
- Private Sourcing Events
- Sell on GoldSupplier.com
- How to Sell
- Post Products
- Manage Products
- Manage Groups
- About
- About Us
- Link to Us
- Contact Us
- Sitemap
- Please Enter your Email Address
- Please enter the content for your inquiry.
We will find the most reliable suppliers for you according to your description.
Send Now-
Winnie Wen
Welcome to my shop! Glad to serve you!Please send your question!
Your message has exceeded the limit.
Your message has exceeded the limit.
-
-
Your inquiry content must be between 20 to 5000 characters.Send Now.
-
Please input the mailbox.
-